background image

5.2 Commissioning 

Commissioning with DALI control unit 

Commissioning depends on the control unit being used. 
The system is fitted and connected. 

Switch on mains voltage. 
Transformer switches to maximum brightness. 

Perform commissioning (see instructions for control unit) 

Commissioning with installation button 

The system is fitted and connected. 

Switch on mains voltage. 
Transformer switches to maximum brightness. 

Press installation button until the transformer starts dimming. 
The transformer has detected the installation button and can now be operated. 

6 Appendix 

6.1 Technical data 

Rated voltage 

AC 230 / 240 V ~ 

Mains frequency 

50 / 60 Hz 

Rated voltage 

DC 230 / 240 V 

Battery voltage 

DC 176 ... 275 V 

Primary current 

0.16 ... 0.5 A 

Rated load 

35 ... 105 W 

Minimum connected load 

35 W 

Standby power 

max. 0.5 W 

Power loss 

max. 6 W 

Power factor 

0.95 

Output voltage 

AC 11.8 V~ eff. 

Ambient temperature 

-20 ... +50 °C 

Housing temperature 

75 °C (tc) 

Protection rating 

IP 20 

Safety class 

II 

Primary side connection 
Single stranded 

0.5 ... 1.5 mm² 

finely stranded with conductor sleeve 

0.5 ... 1.5 mm² 

finely stranded without conductor sleeve 

0.5 ... 1.5 mm² 

Secondary side connection 
Single stranded 

0.75 ... 2.5 mm² 

finely stranded with conductor sleeve 

0.75 ... 2.5 mm² 

single stranded without conductor sleeve 

0.75 ... 2.5 mm² 

Secondary cable length 

0.3 ... 2 m 

Dimensions W×H×D 

170×44×34 mm 

6.2 Troubleshooting 

Device switches off 

Cause: short-circuit protection has tripped. 

Eliminate short-circuit. 

The transformer switches on again after the short-circuit is eliminated 

Light becomes dimmer without being operated and brighter again after some time 

Cause: overheating protection adjusts the power downwards to allow the transformer to cool, 
and then raises it again. 

Check the installation situation. 

82575902 

13.05.2011 

6/7 

DALI Tronic transformer 105 W 

Содержание DALI Tronic Trafo 105 W








Отзывы: