background image

Manual switch-off of the run-
on time

On, Off
Basic setting: Off

Allows manual switch-off of a
running run-on time. If the
parameter is switched off, then
a switch-off command will also
switch the actuator on. Only
visible if a run-on time was
set.

Operating hours

0...65535
Basic setting: Current value

The time is counted during
which the load is physically
switched on.
This parameter can be reset to
"0", for example after
exchanging the load.
The Reset button is used to
reset the meter to "0". The
device must be programmed
to apply the change.

Extended channel settings "switching"

Parameters

Setting options, Basic
setting

Explanations

Operating mode

Normal operation
Continuous on
Continuous off
Basic setting: Normal
Operation

see Device and channels

Manual commissioning

On, Off
Basic setting: On

Blocks manual commissioning
for the device channel.
Note: In the "Off" setting, the
device cannot be reset to the
factory setting.

Local Operation

On, Off
Basic setting: On

Blocks the output for operation
using the 

Prog

 button.

Behaviour on voltage return

 On
 Off
Last value

Basic setting: Off

Defines the behaviour of the
output after voltage return.

Behaviour after the end of the
disabling function

 On
 Off
no change
Last value
Basic setting: No change

Behaviour of the output when
a block is removed.

Manual saving of the scene
values

On, Off
Basic setting: On

Disables the saving of the
current brightness value as
scene value in an actuator for
a command via a transmitter.

32582722

10864994

27.04.2017

12/15

Wireless switching/dimming top unit, 1-gang

Содержание 5490 Series
















Отзывы: