background image

Wireless switching/dimming top unit, 1-gang

Order No. : 5490 ..

Operating instructions

1 Safety instructions

Electrical devices may only be mounted and connected by electrically skilled
persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Always disconnect before carrying out work on the devise or
load. In so doing, take all the circuit breakers into account, which support dangerous
voltages to the device and or load.

Danger of electric shock. The device is not suitable for disconnection from supply
voltage. Depending on the insert used, the load is not electrically isolated from the
mains, even when the device is switched off.

These instructions are an integral part of the product, and must remain with the end
customer.

2 Device components

Figure 1: Device components

(1) FM insert
(2) Frame
(3) Radio button
(4) Status LED

3 Function

Intended use

-

Manual and radio-controlled operation of suitable flush-mounted inserts for switching or
dimming (see accessories)

-

Mounting on flush-mounted insert

-

Operation with suitable radio transmitters

i

No operation on pulse insert, 2-wire and 3-wire extension inserts possible.

1/15

32582722

27.04.2017

Wireless switching/dimming top unit, 1-gang

10864994

Содержание 5490 Series
















Отзывы: