background image

41

ENGLISH

5.5. Charging

Connect the device to power supply with power line.

Note: When the device is closed and the battery is charging up, short press power button and 

the device will display dynamic charge icon, it means that the device is charging up. When the 

battery status is full, the charging has been finished. When the device is open and the battery is 

charging up, the battery status icon on the right top will display dynamically. It means that the 

device is charging up. When the battery status is full, the charging has been finished.

5.6 Reset

Long press the power key to reset.

6 MAINTAIN, TRANSPORT AND STORAGE

6.1 Cleaning and disinfection

Please turn off the device and disconnect it from the power,do not immerse it into liquid.

Use 75% alcohol to wipe the device enclosure, and use liquid soap or isopropanol to wipe the watch-

band for disinfection, nature dry or clean it with clean and soft cloth. Do not spray any liquid on the 

device directly, and avoid liquid penetrating into the device.

6.2 Maintenance

A.  Check the main unit and all accessories periodically to make sure that there is no visible damage that 

may affect peopls safety and monitoring performance. It is recommended that the device should be 

inspected weekly at least. When there is obvious damage, stop using it.

B.  Please clean and disinfect the device before/after using it according to the User Manual (6.1).

C. Recharge  the  battery  soon  after  the  over-discharge.  The  device  should  be  recharged  every  six 

months when it is not regular used. It can extend the battery life following this guidance.

D.  The device need not to be calibrated during maintenance.

E.  Please recharge the battery when the screen shows low power alarm information.

F.  Patients are advised to calibrate the device termly (or according to the calibrating program of hospi-

tal). It also can be performed at the state-appointed agent or just contact us for calibration.

G.  Check the backup power of the device regularly, when it can not support 1-hour continuous opera-

tion, please contact after-sales to replace the battery. 

6.3 Transport and Storage

A.  The packed device can be transported by ordinary conveyance or according to transport contract. 

During transportation, avoid strong shock, vibration and splashing with rain or snow, and it can not 

be transported mixed with toxic, harmful, corrosive material.

B.  The packed device should be stored in room with no corrosive gases and good ventilation. Temper-

ature: -40°C ~ +60°C; Relative humidity: ≤95%.

Содержание OXY-200

























Отзывы: