GigE FC11000GE Скачать руководство пользователя страница 18

Страница: 18 / 37

K09821;18/37

- 18 -

MS=1 SS=7

I D: CAMERA-1

Camera t ype

ID not specified

ID speci fied

(Note) When the pulse width control mode is set for the asynchronous shutter operation or when a shutter setting value is

out of the predetermined range in the partial scan or other operation, the actual time is displayed as “--.-”.

S.FORM:

The current shutter system is displayed. The left is either continuous (NORMAL) or asynchronous
(ASYNC), and the right is either high speed (HIGH) or low speed (LOW).

SCAN:

The current scanning system is displayed. It is either all pixel readout scan (NORMAL) or partial scan
(PARTIAL). (

→

See “Priority relationship among scan mode setting items” described in another section)

●

MENU2

GAIN B:

The gain correction value for the image on the right side is set.

OFFSET B: The offset correction value for the image on the right side is set.

PWC:

Whether the pulse width operation mode is ENABLED or
DISABLED in the asynchronous shutter mode when the
shutter switch is positioned at “9” , is selected.

●

MENU3

BZ:

This is to switch between (ON) and (OFF) for the confirmation
sound to be activated when switch manipulation is made.

BAUD:

The baud rate used for RS-232C communication is displayed.

Vinit2:

The polarity of the trigger signal via CC1 of Camera Link is set.
The factory default is negative logic (NORMAL). When
(INVERTED) is selected, positive logic input is used.

STRB:

The signal (OFF/Exposure timing signal/Busy signal) of STRB
output terminal is set.

●

MENU4

PATTERN:

This is to switch between (ON) and (OFF) for the test pattern
output.

bit:

This is to switch between (8bits),(10bits) and (12bits) for the bit
number of the image output.

FORM.:

This is to switch between (DUAL) and (SINGLE) for the CCD
output form.

ALC(Automatic Level Correction):
This is to switch between (ON) and (OFF) for the Automatic

correction function.

VSUB:

The  setting  value  of  Vsub  voltage  (substrate  voltage  of  CCD
element) is displayed.
Since  the  value  is  optimally  set  before  shipment,  the  user  is
not required to change it as a general rule.

The following items are for display only; they cannot be directly changed
on the menu. These are automatically updated when a corresponding
change is made using the switches:

MS=

The current position of the mode switch is displayed.

SS=

The current position of the shutter setting switch (EXP.) is
displayed.

MF=

The information (16 bits x 2 sets) of the internal mode flags
of the camera (internal flags to determine operation) is displayed in
the hexadecimal system. The details of the internal flags are
described later.

Tc=

The current internal temperature of the camera is displayed in
Celsius. The temperature data are refreshed every 0.4 seconds.

[ID information display]
The ID code and other information set by the user for each camera can be saved in the camera (via serial communication).
The settable maximum number of characters are 15, and alphabets (both upper and lower cases), numbers and some
special symbols such as”+” and “-” excluding the control codes are used.
(

→

Refer to the section of “Serial Communication Control” for the details.)

The ID code set by the user is displayed on the lower left of the “Menu Display of Setting Group 1” by the OSD function;
this allows the user to confirm the setting content (ID: onward).
(If the ID code is not set, the camera type is displayed instead.)
The right figure shows an example where “CAMERA-1” is set as the ID information.

Camera type

[ V. X.XX]

Menu display of Se tting Gr oup 2

MENU2

: ON

GAI NB

OFFSTB :

-4

PWC

: DISABLED

MS=A SS=7

MF=0008.0000