GigE FC11000GE Скачать руководство пользователя страница 14

Страница: 14 / 37

K09821;14/37

- 14 -

6. How to Change Settings

(6-1) How to set shutter speed

The shutter speed is determined mainly by the setting positions of the shutter switch from “0” to “9”.

Table 6-1 Setting value of shutter speed
Position

shutter switch

High speed shutter (continuous/asynchronous)

Low speed shutter (continuous)

DUAL output

SINGLE output

DUAL output

SINGLE output

No shutter (continuous)

1/ 5 second

1/ 2.7 second

1/ 5 second

1/ 2.7 second

1/ 2000 second

1/ 1200 second ( 5H)

1/ 2.6 second

1/ 1.35 second ( 2V)

1/ 1000 second

1/ 530 second ( 13H)

1/ 1.7 second

1/ 0.90 second ( 3V)

1/ 500 second

1/ 260 second ( 28H)

1/ 1.3 second

1/ 0.68 second ( 4V)

1/ 250 second

1/ 130 second ( 56H)

1/ 1.0 second

1/ 0.54 second ( 5V)

1/ 120 second

1/ 60 second ( 117H)

1/ 0.86 second

1/ 0.45 second ( 6V)

1/ 60 second

1/ 32 second ( 237H)

1/ 0.74 second

1/ 0.39 second ( 7V)

1/ 30 second

1/ 16 second ( 475H)

1/ 0.65 second

1/ 0.34 second ( 8V)

1/ 15 second

1/ 8 second ( 952H)

1/ 0.57 second

1/ 0.30 second ( 9V)

1/ 7.5 second

1/ 4 second (1906H)

1/ 0.52 second

1/ 0.27 second ( 10V)

Pulse width control /asynchronous (!)

(Note) (H) and (V) in the table represent the horizontal time unit and the vertical time (frame duration) unit respectively.
(Note) The values in the table are the shutter speed in all pixels scanning, they get longer in 2 lines binning scanning.

Confirm it in OSD(On screen display) for details.

(Note) ”No shutter” in the table means the continuous shutter mode with exposure time = 1 frame duration.
(Note) The value of the each shutter speed is the factory default value. The shutter speed of each position (excluding

shutter position = 0) is possible to change by the user in the operation mode [Group 1].

(!) As for this camera, “Pulse width control time/asynchronous” must be set to be “Pulse width control (PWC) =

ENABLED”. When it is set to be “Pulse width control (PWC) = DISABLED” (default), the selection can be made out of
the 9 levels not only for the continuous shutter operation but also for the asynchronous shutter operation.

(6-2) How to set operation mode

The setting items of the operation modes are divided into 4 groups of Group 1, Group 2, Group 3 and Group 4 as follows:

Group 1 ············ Group1 is mainly used for setting the basic operation (Shutter speed, Gain etc.). After start-up, set the

mode switch to the position corresponding to the item to be changed and then manipulate the
UP/DOWN switch to change the setting.

Group 2 ············ Group2 is mainly used for setting

the auxiliary function (Gain correction etc.)

After start-up, set the mode switch to the position corresponding to the item to be changed and then

manipulate the UP/DOWN switch to change the setting.

Group 3 and 4 ···· These are mainly used for setting the configuration items (Terminology below).

After start-up, set the mode switch to the position corresponding to the item to be changed and then
manipulate the UP/DOWN switch to change the setting.

(Note) When any setting item is changed, it must be saved in one of the program pages from “A” to “F” before turning off

the power to store the data in the memory of the camera. Carefully note that the new setting is not automatically
saved and that the prior setting will be effective at the next time of power-on if the power is turned off before storing
it. The configuration items, however, are automatically saved whenever they are changed.

[Terminology] Configuration items ···· They are the common setting items that are independent of the program pages.

These items are automatically saved in the internal EEPROM at the same time as
they are changed by manipulating the switches on the rear panel.