Gigaset M101 Data Скачать руководство пользователя | Manualshive

Страница: 14 / 37

background image

Configuration program options

14

gigam101.fm5

21.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

"Operating mode" tab

Important:

If one station is set to "AT commands, local" or "AVM/Eumex

commands, local", the other station must switch to the corre-

sponding "AT commands, remote" or "AVM/Eumex commands,

remote" operating mode. And if one station is switched to "Di-

rect connection", the other station must also be switched to this

mode. The appropriate switches are performed automatically if

you select an operating mode for an Gigaset M101 Data unit.

Setting the operating mode

Open the

Operating mode

tab and select one of the five modes:

The three connection types are used for different purposes:

Direct connection The transmission parameters for the PC’s

COM port are manually set at the compu-

ter without automatic baud rate or data for-

mat recognition. This is always useful if the

device at the Partnerstation does not sup-

port baud rate or data format recognition

as performed by conventional modems,

e.g. in the case of a second PC.

AT commands

lokalen Station

(PC)

➔

page 33

Automatic recognition of the transmission

parameters based on the data from the PC

at the lokalen Station.

AT commands

Partnerstation

(device)

➔

page 33

Automatic emulation of the transmission

parameters based on the values received

from the PC at the Partnerstation.

AVM / Eumex

lokalen Station

(PC)

➔

page 34

Automatic recognition of the AVM / Eumex

transmission parameters based on the

data from the PC at the lokalen Station.

«
...
12
13
14
15
16
...
»

Содержание M101 Data






































Отзывы:

Нет отзывов

Похожие инструкции для M101 Data

Бренд: IBM Страницы: 86

System x3630 M4

Бренд: IBM Страницы: 7

Бренд: Watchguard Страницы: 24

IMACS Network Device

Бренд: Zhone Страницы: 114

Бренд: SAGEMCOM Страницы: 75

Бренд: Techroutes Страницы: 20

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

Бренд: Digisol Страницы: 81

Бренд: Tripp Lite Страницы: 2

Бренд: ZALMAN Страницы: 16

Бренд: VideoWave Страницы: 12

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренд: ALIBI Страницы: 232

Бренд: Draytek Страницы: 17

Бренд: ZyXEL Communications Страницы: 4

Бренд: XtendLan Страницы: 17

BreezeNET DS.11 Configuration Utility

Бренд: Alvarion Страницы: 2

com.tom INDUSTRY 100.WLAN.W

Бренд: Beck Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды