Gigabyte G492-Z51 Скачать руководство пользователя страница 78

Страница: 78 / 117

BIOS Setup

- 78 -

5-2-18

MAC IPv4 Network Configuration

Parameter

Description

Configured

Indicates whether network address is configured successfully or not.

Options available: Disabled/Enabled. Default setting is

Disabled

Enable DHCP

(Note)

Options available: Enabled/Disabled. Default setting is

Enabled

Local IP Address

(Note)

Press [Enter] to configure local IP address.

Local NetMask

(Note)

Press [Enter] to configure local NetMask.

Local Gateway

(Note)

Press [Enter] to configure local Gateway

Local DNS Servers

(Note)

Press [Enter] to configure local DNS servers

Save Changes and Exit

Press [Enter] and then choose to save or discard the changes made.

(Note) This item will appear on the screen when

Configured

is set to

Enabled

Содержание G492-Z51






















































































































Результаты поиска

Содержание G492-Z51

Отзывы:

Похожие инструкции для G492-Z51

Бренды по названию

Популярные бренды

Gigabyte G492-Z51, Руководство пользователя

Результаты поиска

Содержание G492-Z51

Отзывы:

Похожие инструкции для G492-Z51

Бренды по названию

Популярные бренды