manualshive.com logo in svg

Gigabyte G152-Z12, Руководство пользователя, Страница: 33 / 140

Поделиться
Скачать
Gigabyte G152-Z12 Скачать руководство пользователя страница 33

- 33 -

System Hardware Installation

3-5  Installing the Hard Disk Drive

Read the following guidelines before you begin to install the Hard disk drive:
•  Take note of the drive tray orientation before sliding it out.

•  The tray will not fit back into the bay if inserted incorrectly.

•  Make sure that the HDD is connected to the HDD connector on the backplane.

Follow these instructions to install a 2.5" hard disk drive: 

1.  Loosen the thumbnail screw securing the hard drive cage.
2.  Lift up the hard drive cage and remove it from the system.

3.  Extend the locking lever.

4.  Pull the locking lever to remove the HDD tray. 

5.  Align the hard disk drive with the positioning stub on the HDD tray.

6.  Slide hard disk drive into the blank HDD tray.

7.  Reinsert the HDD tray into the slot and close the locking lever.

1

2

3

5

4

6

Содержание G152-Z12













































































































































Отзывы:

Нет отзывов