manualshive.com logo in svg

Giga-tronics GT-1000B, Руководство по эксплуатации, Страница: 23 / 26

Поделиться
Скачать
Giga-tronics GT-1000B Скачать руководство пользователя страница 23

Giga-tronics GT-1000B Microwave Power Amplifier   

Performance Verification 

Operation Manual, Part Number 34672-001, Rev. A, May 2013 

Page 17 

Table 15: GT-1000B Performance Verification Procedure 

GT-1000B Performance Verification Procedure 

Step 

Action 

1.

 

 Connect the test equipment to the GT-1000B as shown in 

Error! Reference source not found.

 

on the previous page. Note the following: 

•

 

The high power attenuator should be characterized at the test frequencies noted in the 

Table 16 on page 18. Use this characterization as an offset in the power measurement. 

Connecting the V/GHz output of the synthesizer to the V prop F input of the power meter 

simplifies measurements when changing the test frequency. 

•

 

Consult the manufacturer’s Operation’s Manual for the power meter and signal generator 

for proper configuration. 

2.

 

 Energize all of the equipment in the test setup, and let the equipment warm up for 30 minutes. 

3.

 

 If an attenuator is used between the sensor and output, measure the insertion loss of the 

attenuator and interconnect cable. 

4.

 

 Set the 2520B frequency to 2 GHz (Standard GT-1000B) or 100 MHz (GT-1000B Option 06), the 

frequency step size to 1 GHz (Standard GT-1000B) or 100 MHz (GT-1000B Option 06), and the RF 

output power level to +5 dBm. 

5.

 

 If an automatic frequency correction configuration is not available, input the test frequency into 

the power meter. 

6.

 

 Energize the RF output of the 2520B microwave signal generator. 

7.

 

 Measure the maximum output power from the GT-1000B and enter the value in the appropriate 

place on the Performance Verification Datasheet on the next page. 

8.

 

 Increase the frequency on the 2520B as indicated in the Performance Verification Datasheet. 

Measure the output power and record on the Performance Verification Datasheet. 

9.

 

 Repeat step 8 until the power measurements for all of the frequencies shown in the 

Performance Verification Datasheet have been taken. 

10.

 

 Compare the measured results with the Specifications value. If the measured values are not 

within the specifications, contact Giga-tronics for assistance. 

End of Procedure 

 
 

 

 

Содержание GT-1000B



























Отзывы:

Нет отзывов