background image

1-7  Back Panel Connectors

USB 3.2 Gen 1 Port

The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0 

specification. Use this port for USB devices.

SMA Antenna Connectors (2T2R)

Use this connector to connect an antenna.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.

DisplayPort

DisplayPort delivers high quality digital imaging and audio, supporting bi-directional audio transmission. 

DisplayPort can support HDCP 2.3 content protection mechanisms. You can use this port to connect your 

DisplayPort-supported monitor. Note: The DisplayPort Technology can support a maximum resolution of 

4096x2304@60 Hz but the actual resolutions supported depend on the monitor being used.

After installing the DisplayPort device, make sure to set the default sound playback device to 

DisplayPort. (The item name may differ depending on your operating system.)

USB 3.2 Gen 2 Type-A Port (Red)

The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1 

and USB 2.0 specification. Use this port for USB devices.

USB 3.2 Gen 2 Type-A Port (Red) (Q-Flash Plus Port)

The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1 and 

USB 2.0 specification. Before using Q-Flash Plus 

(Note)

, make sure to insert the USB flash drive into this port first.

USB Type-C

®

 Port

The reversible USB port supports the USB 3.2 Gen 2x2 specification and is compatible to the USB 3.2 

Gen 2, USB 3.2 Gen 1, and USB 2.0 specifications. Use this port for USB devices.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 2.5 Gbps data rate. The following 

describes the states of the LAN port LEDs.

Tighten the antennas to the antenna connectors and then aim the antennas correctly for better 

signal reception.

Connection/

Speed LED

Activity LED

LAN Port

Connection/Speed LED:

State 

Description

Green

2.5 Gbps data rate

Orange

1 Gbps data rate

Off

100 Mbps data rate

Activity LED:

State 

Description

Blinking

Data transmission or receiving is occurring

On

No data transmission or receiving is occurring

(Note)  To enable the Q-Flash Plus function please visit the "Unique Features" webpage of GIGABYTE's 

website.

- 13 -

Содержание Z590 AORUS ULTRA





























































Отзывы: