GIGA-BYTE TECHNOLOGY MZ72-HB2 Скачать руководство пользователя

Страница: 21 / 124

- 21 -

Hardware Installation

6/7/8) CPU0_FAN//CPU1_FAN/SYS_FAN1/SYS_FAN2/SYS_FAN3/SYS_FAN4
(CPU FAN/System FAN Headers)

The motherboard has two 4-pin CPU fan header (CPU_FAN), and four 4-pin (SYS_FAN) system fan headers.

Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect

it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU

fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat

dissipation, it is recommended that a system fan be installed inside the chassis.

Pin No. Definition

GND

+12V

Sense

Speed Control

•

Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•

These fan headers are not configuration jumper blocks. Do not place a jumper cap on the

headers.

Содержание MZ72-HB2





























































































































Результаты поиска

Содержание MZ72-HB2

Отзывы:

Похожие инструкции для MZ72-HB2

Бренды по названию

Популярные бренды

GIGA-BYTE TECHNOLOGY MZ72-HB2, Руководство пользователя

Результаты поиска

Содержание MZ72-HB2

Отзывы:

Похожие инструкции для MZ72-HB2

Бренды по названию

Популярные бренды