background image

6

Specifications

Model SP200HT

 

U.S. 

(Metric)

Volume @ 900 RPM

 .............................................

6.1 GPM/366 GPH

 ......

(23.0 L/min/1386 L/hr)

Volume @ 750 RPM

 .............................................

5.0 GPM/300 GPH

 ......

(19.1 L/min/1136 L/hr)

Discharge Pressure ..............................................

870 PSI

 ..............................................

(60 bar)

Power Consumption .............................................

4.0 BHP

 ...............................................

3.0 kW

Plunger Diameter ..................................................

0.94”

 ..................................................

(24 mm) 

Stroke ...................................................................

0.79”

 ..................................................

(20 mm)

Crankcase Oil Capacity ........................................

24 fl.oz.

 ..............................................

(710 ml)

Temperature of Pumped Fluids @ 900 RPM

 ........

194 

o

F ..................................................

(90

o

 C)

Temperature of Pumped Fluids @ 750 RPM

 ........221 

o

F ................................................

(105

o

 C)

Inlet Ports...................................................................................................................

(2) 3/4” NPT

Discharge Ports .........................................................................................................

(2) 1/2” NPT

Crankshaft Mounting....................................................................................................Either Side

Shaft Rotation .......................................................Top of Pulley Towards Fluid End

Weight ...................................................................

31.3 lbs. 

 ...........................................

(14.2 kg)

NPSHR (900 RPM)

 ...............................................

20.3 ft. of head

 .................................

6.2 mWs

Consult the factory for special requirements that must be met if the 

pump is to operate beyond one or more of the limits specified above. 

PULLEY INFORMATION

Pulley selection and pump speed are based on 

a 1725 RPM motor and “B” section belts.  When 

selecting desired GPM, allow for a ±5% tolerance 

on pumps output due to variations in pulleys, belts 

and motors among manufacturers.

1.  Select GPM required, then select appropriate 

motor and pump pulley from the same line.

2.  The desired pressure is achieved by selecting 

the correct nozzle size that corresponds with the 

pump GPM. 

HORSEPOWER INFORMATION

Horsepower ratings shown are the power re-

quirements for the pump.  Gas engine power 

outputs must be approximately twice the pump 

power requirements shown above.

We recommend that a 1.1 service factor be speci-

fied when selecting an electric motor as the power 

source.  To compute specific pump horsepower 

requirements, use the following formula:
   

 

 

(GPM X PSI) / 1460 = HP

SP200HT HORSEPOWER REQUIREMENTS

RPM GPM

GPH

200 PSI

400 PSI

600 PSI

870 PSI

250

1.7

102.0

0.23

0.47

0.70

1.02

500

3.4

204.0

0.47

0.94

1.41

2.04

750

5.0

300.0

0.69

1.38

2.07

3.00

900

6.1

366.0

0.84

1.68

2.52

3.66

200

Содержание SP100HT













Отзывы: