Giandel PS-4000QAR, Руководство пользователя, Страница: 5 / 7

1. High power load connection
If the electrical appliance power is higher than a single socket max output power, please
connect it to the ac output terminal.
2. Connection of the remote control box
Directly to the two ends of the cable respectively inserted into the inverter and wired
remote control remote control box on the interface.
7. USAGE
①
. How to use inverter
1) Check the output voltage and capacity of the battery to make sure it is in accord with the
requirements of the product.
2) Connect the battery and the DC cable of the inverter to ensure that the polarities are not
connected reversely and in tight connection.
3) Long press the switch or the remoter of inverter for over 0.5s and then stop, if the
indicator light on the inverter or on the remote control box is on, it means that the
inverter starts to work normally. This opening method can avoid turning on the unit by
mistakes due to the interference or any factors.
4) Switch off electrical appliances and put its plug to the AC output socket of inverter. Then
switch on electrical appliance.
5) The cooling fans inside the inverter do not work until the case temperature rises up to
about 40
℃
or the load power is more than 40% of rated power.
6) Switch off inverter and remoter to stop working. At that time, the indicator lights in. Both
inverter and remoter are off. The inverter does not consume current of the battery when
it is switched off.
②
How to use USB power supply
This model with USB output, can provide stable voltage 5V DC, maximum current 2.4A
directly for the portable device with USB port.
Notice: Before using the USB power supply, please make sure the device can be charged
by USB and the maximum working current is no more than 2.4A.
6.
Notice:
(1) The table above is only for your reference. In practice, the thick wire can be replaced
by two thin parallel wires if only the total cross-sectional area of the wire meets the
requirements.
(2) In high current, the input DC wire may produce voltage drop, therefore, the operating
voltage should be subject to the value on the terminals. If the voltage drop is too large,
you can increase the cross-sectional area or reduce the length of the lead.
(3) Connect cathode wire of the battery to the cathode terminal (black) on the rear panel of
inverter and then connect the anode wire of the battery to the anode terminal (red) on
the inverter, and fix them.
Warnings:
(1) Please wear eye patch and work clothes when working around the battery to protect
your eyes and skin from the acid and corrosive objects.
(2) Prepare enough water and soap. In case the acid material splashes on your skin, clean
it by soap and water as soon as possible. If the acid material spays to your eyes
accidentally, clean it by cold water and then sent to hospital.
(3) Do not put any combustible material in the location of installation for it will result in
spark when connected to the battery.
(4) Keep good ventilation. The battery may produce a little inflammable gas when it works,
so keep away from the inverter and it is better to install them in different space.
(5) Fix the connecting wire of the input DC, or it will result in the over- reduction of the
voltage or over-temperature of the inverter.
(6) Reverse connection of the polarities or the short circuit will burn the fuse or result in
the permanent damage of the internal elements of inverter.
(7) Take away the metal accouterments, such as ring or watch, when installation, to avoid
the short circuit.
(8) Although there is over-voltage protection, it may also cause damage of the inverter if
the input voltage is too high.
3) Connection of the AC appliance
Put the load power plug of the AC appliance into the output AC receptacle of the inverter
directly.
Warnings:
(1) Make sure that the switches of the inverter and the appliances are in OFF position
before connection.
(2) Check the power cord. If it is damaged, it should be connected after replacement.
(3) Connection of the AC appliance: Put the power plug of the AC appliance load into the
output AC receptacle of the inverter directly.
Warnings:
Make sure that the switches of the inverter and appliance power are in OFF position
before connection.
Check the power cord. If it is damaged, it should be connected after replacement.
Each output socket of the inverter has a rating current given by manufacturer. Don't
exceed the value in operation, or the socket will be damaged because of over temperature
and it may cause electric shock. For the max output power of the single socket, see the
following tables:
Output socket AC output voltage
Single socket
max output current
Single socket
max output power
110~120VAC
220~240VAC
220~240VAC
220~240VAC
15A
16A
13A
10A
1500W
3000W
2500W
2000W
220~240VAC 13A 2500W