background image

 

 

   

Foreword 

This installation & operating manual will help you 
use the following types of equipment safely and 
efficiently for their intended purpose. 

 

MK 45-1 

 

MK 45-2 

 

MK 45 A-1 

 

MK 45 A-2 

  

These steam traps will be called equipment in this 
document. 

  

This installation & operating manual is intended for 
anyone commissioning, using, operating, servicing, 
cleaning or disposing of this equipment and, in 
particular, for professional after-sales service 
technicians, qualified personnel and authorised and 
trained staff. 
All of these persons must read and understand the 
content of this installation & operating manual. 
Following the instructions given in this installation & 
operating manual helps avoiding danger and 
increases the reliability and service life of the 
equipment. Please note that in addition to the 
instructions given in this installation & operating 
manual you must also observe all locally applicable 
rules and regulations concerning the prevention of 
accidents as well as approved safety guidelines for 
good professional practice. 

  

Availability 

Keep this installation & operating manual together 
with the plant documentation for future reference. 
Make sure that this installation & operating manual 
is available to the operator.  
The installation & operating manual is part of the 
equipment. Please hand over this installation & 
operating manual when selling the equipment or 
passing it on. 

  

Formatting features in the 

document 

Certain text elements of this installation & operating 
manual feature a specific typographic design. You 
can easily distinguish the following text elements: 
Standard text 

Cross-reference

 

 

Listing 

 

Sub-items in listings 

 

Steps for action. 

 

Here you will find additional useful 
information and tips serving to assist you 
in using the equipment to its fullest 
potential. 

Safety 

Use for the intended purpose 

The following thermostatic/thermodynamic steam 
traps are installed in steam lines: 

 

MK 45-1 

 

MK 45-2 

 

MK 45 A-1 

 

MK 45 A-2 

This equipment is designed for discharging 
condensed water or air-venting pipes. 
The equipment must only be used within the 
allowable pressure and temperature limits and only 
if the chemical and corrosive influences on the 
equipment are taken into account. 
Do not expose the control membrane of the 
membrane regulator capsule to superheat 
conditions above 5 °C. 
Correct use includes compliance with the 
instructions given in this installation & operating 
manual, in particular obedience to all safety 
instructions.  
Any other use of the equipment is considered to be 
improper. 

Содержание RHOMBUSline MK 45 A-1





























Отзывы: