P.4
P.5
產品結構
Product Structure
防倒流裝置
超溫及超壓排放閥
發熱線 (內部)
排水管
混合龍頭
恆溫器
花灑頭
入水位 (冷)
出水位 (熱)
1
2
3
4
5
6
7
8
9
Anti Back Siphonage Device
Pressure & Temperature
Relief Valve (PTV)
Heating Element (Inside)
Drain
Lever Mixer
Thermostat
Shower Head
Inlet (Cold)
Outlet (Hot)
1
2
3
4
5
6
7
8
9
1
2
4
9
3
4
5
8
6
7
安裝圖
Installation Diagram
排水
Drain
進水
Inlet
出水
Outlet
熱水器
Water Heater
混合水制
Mixing Valve
外碼
進水
Inlet
出水
Outlet
Mounting
Bracket
排水
Drain
排水
Drain
使用外碼時注意：
確定爐
的安裝位置後，請先用螺
絲將外碼固定在牆上，再
將爐後蓋上的方孔對準固
定在牆上的外碼，向下將
爐穩靠地固定掛在牆上。
Caution:
After confirmation
of installation location,
properly secure the mounting
bracket with screws on the
wall, align the holes of the
back plate of the water
heater with the mounting
bracket, and downwardly
hang the water heater.
安裝說明
Installation Instructions
Positioning
Position water heater near water tap / point of
use in order to minimize heat loss. For wall-mount
style, appropriate anchor screws must be used
and wall should be strong enough to withstand the
weight of water heater. Keep a minimal distance
between wall and water heater. you can also use
the mounting bracket for positioning.
Connecting PTV and Inlet/Outlet Pipes
A Pressure & Temperature Relief Valve (PTV) is
supplied with each GPU water heater. Water will be
released through the PTV when water temperature
reaches 90˚C or when water pressure reaches
1000 kPa in the inner tank. (It is normal that small
amount of water may drip out.)
PTV and water inlet & outlet must be installed
according to the following instructions:
1. Fit PTV to the marked position (normally it is
located on the upper side of the water heater
and is labeled “PTV”).
2. When connecting the pipe,the PTV must point
downward.The outlet of the discharge pipe
connecting the PTV must be positioned
approximately 25-50mm away from the ground,
so that it is easily observable when hot water is
being drained to ensure safety.
3. Connect the inlet pipe (blue) with water supply.
Then connect the outlet pipes (red) with supply
pipe leading to points of use. The diameter of
piping should be 1/2” BSP.
4. Turn on the hot water tap. Turn on water supply
switch until the inner tank has been filled up
with water. The inner tank has been filled up
when water flows from the water tap.
安裝定位
熱水器應盡量安裝於接近出水龍頭之位置，以
減省熱量損耗。
掛牆型號須以膨脹螺絲安裝於能負重之牆壁位
置上，並調整至緊貼牆壁為佳， 你也可以使用
外碼將熱水器固定。
排放閥及水喉接駁
每部GPU熱水器均附上超溫及超壓感應排放閥
(簡稱PTV) 一枚，當內膽水溫升至90℃或水壓
達至1000 kPa 時，熱水會經PTV排出。(如有
少量水滴出，乃正常現象。)
PTV及出入水喉必須按照以下指示安裝︰
1. 取出PTV，安裝於指定位置(通常設在熱水器
上半部側面，並貼有PTV標示) 。
2. 連接水管時，PTV必須向下垂。PTV接出之
排水喉需離地約25mm至50mm，以便排出
熱水時容易察覺，確保安全。
3. 將自來水喉接駁到入水喉 (藍色)，再由出水
喉(紅色) 接駁水喉通往各個出水龍頭。水喉
管件直徑應為1/2”英吋。
4. 接駁妥當後，打開出水龍頭 (紅色熱水掣)，
然後打開水源總掣讓自來水注入熱水器內。
當水從龍頭流出，表示內膽滿溢，此時可關
掉紅色熱水掣。
安裝前注意
安裝必須使用原廠配件。若不按指示方法安
裝及使用而引致任何損壞，本公司概不負責。
安裝工作應由專業持牌水電技術人員負責。
Pre-Installation Notice
Installation should be done by a licensed
technician using the supplied parts. German Pool
is not responsible for any defect or damage
caused by incorrect or unauthorized installation.