常見故障及處理
Trouble Shooting
P. 07
使用中如發現電磁爐操作上有問題，在送回本公司維修前請先依照下表進行檢查﹕
When you run into any problem operating this product, use the table below to troubleshoot the problem.
If the problem persists, contact our Repair & Customer Service Centre.
故障現象
檢查要點
處理方法
峰鳴器斷續鳴響且鍋具不加熱
Buzzer beeps continuously and
pan is not heated
在正常運作時停止加熱
Induction cooker stops heating
during normal operations
保溫失控
Temperature fluctuates
•鍋具不適應
•鍋具位置不合適
•Is the pan not suitable for
induction cooking?
•Is the pan positioned
properly?
•是否空鍋或溫度過高
•吸氣口或排氣口是否堵塞
•室溫太高
•Is the pan empty or cooking
temperature too high?
•Are the air inlet and outlet
being blocked?
•Is the surrounding tempera
ture too high?
•鍋底是否凹凸不平
•Is pan bottom not flat?
接通電源，按
“開/關鍵”鍵，
電磁爐無反應
Power is connected, but the
induction cooker does not
respond when the On/Off
button is pressed
•是否停電?
•府上的自動開關或
保險絲是否發生短路?
•插頭是否脫落或接觸不良?
•Is there a power shortage in
your area?
•Is there a short circuit in the
power source of your home?
•Is the power plug too loose
or not connected well?
電源恢復後再使用
檢查短路原因，排險後才使用
插牢或更換插孔後使用
Try again after power supply
resumes
Find out the cause of short
circuit and eliminate it before
switching on the cooker again
Re-connect the plug or replace
the power jack
使用電磁爐適用之鍋具
將鍋具放置在電磁爐面板中心
Use an appropriate pan
Position the pan in the centre
of cook top
防止乾燒，降溫後自動繼續
待機件冷卻後才使用，並注意
保持內部通風
室溫降低後才使用
Avoid operating cooker with an
empty pan. Let cooker cool
down before switching it on
again
Remove obstruction from the
vent. Let induction cooker cool
down and try again
Try again after the room cools
down
更換平底鍋具後使用
Replace pan with a
flat-bottomed one
* 以上為常見故障的判斷與檢查，只供用戶作參考之用
* 如遇故障切勿自行修理，避免發生危險及對機件造成損害，請立即找專業技術人員或聯絡本公司作出適當維修
*
Above table enlists the most common problems regarding the operations of the product and their possible causes as well as suggested solutions.
It is strictly for users’ reference only
*
Should there be any product malfunction or breakdown, DO NOT repair it yourself. Contact our Repair & Customer Service Centre or consult a
licensed technician immediately
技術規格
Technical Specifications
P. 08
常見故障及處理
Trouble Shooting
型號
Model
電壓/頻率
Voltage/Frequency
額定功率
Power Output
機身尺寸
Dimensions
淨重
Net Weight
總重
Gross Weight
功率調校範圍
Power Adjustment Range
溫度調校範圍
Temperature Adjustment Range
生產標準
Manufacturing Standards
GIC-DF20BB
220 V / 50 Hz (A.C.)
2000 W
(H) 55 mm
(W) 294 mm
(D) 342 mm
Approx. 2.0 kg
Approx. 2.5 kg
500W - 2000W
60 ℃ - 270 ℃
GB4706.1-1992, GB4706.29-1992
本產品之外型、機件或規格如有任何變更，恕不另行通知
Product appearance, structure and specifications are subject to change without prior notice
本說明書內容之中英文版本如有出入，一概以中文版為準
If there is any inconsistency or ambiguity between the English version and the Chinese version of these operating instructions,
the Chinese version shall prevail.
故障代碼
Code
E0
E3*
E4*
E5
故障代碼
Code
E6
E7
E8
E9
EA
故障說明
Error
無鍋具 / 鍋具不合適
No cookware / Inappropriate cookware
電壓過高
Voltage over-loaded
電壓過低
Voltage under-loaded
爐面感應器斷路
Open circuit of cook top sensor
故障說明
Error
爐面感應器短路
Short circuit of cook top sensor
爐面過熱
Cook top overheat
機內溫度感應器短路
Short circuit of internal temperature sensor
機內溫度感應器斷路
Open circuit of internal temperature sensor
機內溫度過高
Internal overheat
* E3 及 E4並不屬於機器故障，待電壓恢復後(187V – 250V) 即可使用
*
E3 & E4 are not product errors. Operation can be resumed when power voltage returns to normal rating (187V - 250V)
