background image

25

 

V1.0 July 2020

 

12.0

 

LIMITED WARRANTY

 

  

The manufacturer, 

Geosense Ltd

, warrants the 

Geosense

®

 HLC

-

6000 Series Hydraulic 

Anchor Load Cells 

manufactured by it, under normal use and service, to be free from 

defects in material and workmanship under the following terms and conditions:

  

The 

Geosense

®

 HLC

-

6000 Series Hydraulic Anchor Load Cells 

shall be installed in 

accordance with the manufacturer

s recommendations.

 

  

The equipment is warranted for 2 years from the date of shipment from the manufacturer to 

the purchaser.

 

  

The warranty is limited to replacement of part or parts which, are determined to be defective 

upon inspection at the factory. Shipment of defective part or parts to the factory shall be at the 

expense of the Purchaser. Return shipment of repaired/replaced part or parts covered by this 

warranty shall be at the expense of the Manufacturer.  

 

  

Unauthorised alteration and/or repair by anyone which, causes failure of the unit or 

associated components will void this 

LIMITED WARRANTY

 in its entirety.

 

  

The Purchaser warrants through the purchase of the Geosense

®

 HLC

-

6000 Series 

Hydraulic Anchor Load Cells  that he is familiar with the equipment and its proper use.  

In no event shall the manufacturer be liable for any injury, loss or damage, direct or 

consequential, special, incidental, indirect or punitive, arising out of the use of or 

inability to use the equipment sold to the Purchaser by the Manufacturer. 

 

 
 

The Purchaser assumes all risks and liability whatsoever in connection with the 

Geosense

®

 

HLC

-

6000 Series Hydraulic Anchor Load Cells 

from the time of delivery to Purchaser.

 

Содержание HLC 6000 Series



























Отзывы: