background image

 

 
 

 

Warranty Statement 

Geokon, Inc. warrants its products to be free of defects in materials and workmanship, under 

normal use and service for a period of 13 months from date of purchase. If the unit should 

malfunction, it must be returned to the factory for evaluation, freight prepaid. Upon examination 

by Geokon, if the unit is found to be defective, it will be repaired or replaced at no charge. 

However, the WARRANTY is VOID if the unit shows evidence of having been tampered with or 

shows evidence of being damaged as a result of excessive corrosion or current, heat, moisture or 

vibration, improper specification, misapplication, misuse or other operating conditions outside of 

Geokon's control. Components which wear or which are damaged by misuse are not warranted. 

This includes fuses and batteries. 

Geokon manufactures scientific instruments whose misuse is potentially dangerous. The 

instruments are intended to be installed and used only by qualified personnel. There are no 

warranties except as stated herein. There are no other warranties, expressed or implied, including 

but not limited to the implied warranties of merchantability and of fitness for a particular purpose. 

Geokon, Inc. is not responsible for any damages or losses caused to other equipment, whether 

direct, indirect, incidental, special or consequential which the purchaser may experience as a 

result of the installation or use of the product. The buyer's sole remedy for any breach of this 

agreement by Geokon, Inc. or any breach of any warranty by Geokon, Inc. shall not exceed the 

purchase price paid by the purchaser to Geokon, Inc. for the unit or units, or equipment directly 

affected by such breach. Under no circumstances will Geokon reimburse the claimant for loss 

incurred in removing and/or reinstalling equipment. 

Every precaution for accuracy has been taken in the preparation of manuals and/or software, 

however, Geokon, Inc. neither assumes responsibility for any omissions or errors that may appear 

nor assumes liability for any damages or losses that result from the use of the products in 

accordance with the information contained in the manual or software. 

Содержание GK-401
















Отзывы: