TABLE of CONTENTS
1. INTRODUCTION .................................................................................................................................................. 1
2. INSTALLATION INSTRUCTIONS .................................................................................................................... 2
2.1.1 Assembling the Spacer Block into the Crackmeter ..................................................................................... 2
2.1.2 Mounting the Crackmeter ........................................................................................................................... 3
3. TAKING READINGS ............................................................................................................................................ 4
3.3.1 Taking Readings with a Dial Indicator ...................................................................................................... 4
3.3.2 Taking Readings with a Depth Micrometer ................................................................................................ 5
APPENDIX A. SPECIFICATIONS .......................................................................................................................... 6
FIGURES
F
IGURE
1
-
4415-5
C
RACKMETER WITH
S
PACER
B
LOCK
I
NSTALLED
............................................................................. 2
2
R
EADING
L
OCATIONS FOR
M
ODELS
4415-1
&
4415-3 ................................................................................. 4
3
ODEL
4415-5 ................................................................................................... 4
TABLES
T
ABLE
PECIFICATIONS
............................................................................................................................................ 6
