Genie SX-150 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 77

background image

Operator's Manual

Second Edition • Third Printing

Specifications

72

SX-150 • SX-180

Part No. 1262335

Specifications

Model

SX-150

Height, working maximum

158 ft

48.16 m

Height, platform maximum

152 ft

46.33 m

Height, stowed maximum

10 ft

3.05 m

Horizontal reach, maximum

80 ft

24.38 m

Width, axles retracted

8 ft 2 in

2.49 m

Width, axles extended

16 ft 6 in

5.03 m

Length, stowed

53 ft1 in

16.18 m

Length, stowed for transport
(jib stowed for transport)

42 ft 8 in

13 m

Maximum load capacity

750 lbs

340 kg

Maximum wind speed

28 mph

12.5 m/s

Wheelbase, axles extended

15 ft 6 in

4.72 m

Wheelbase, axles retracted

16 ft 6 in

5.03 m

Ground clearance

15 in

38.1 cm

Turning radius, axles extended

Inside

9 ft 11 in

3.02 m

Outside

24 ft 1 in

7.34 m

Turning radius, axles retracted

Inside

20 ft 7 in

6.27 m

Outside

28 ft 1 in

8.56 m

Turntable rotation (degrees)

360° continuous

Turntable tailswing, axles
extended

3 ft 6 in

1.07 m

Turntable tailswing, axles
retracted

3 ft 9 in

1.14 m

Controls

12V DC proportional

Platform dimensions, 6 foot
(length x width)

72 x 30 in 183 x 76 cm

Platform dimensions, 8 foot
(length x width)

96 x 36 in 244 x 91 cm

Platform leveling

self-leveling

Platform rotation

160°

Vertical jib rotation

135°

Horizontal jib rotation

60°

AC outlet in platform

standard

Fuel tank capacity

50 gallons

189 liters

Hydraulic pressure, maximum
(boom functions)

2900 psi

203 bar

Hydraulic pressure, maximum
(auxiliary power unit)

3200 psi

221 bar

System voltage

12V

Tire size

445D50/710, 18 ply HD FF

Weight

49,950 lbs

22,657 kg

(Machine weights vary with option configurations. See
serial label for specific machine weight.)

Maximum slope rating, stowed position, 4WD

Counterweight uphill

35%

19°

Counterweight downhill

35%

19°

Side slope

25%

14°

Note: Slope rating is subject to ground conditions with
one person in the platform and adequate traction.
Additional platform weight may reduce slope rating.

Drive speeds

Drive speed, stowed

2.3 mph

40 ft/11.8 sec

3.7 km/h

12 m/11.8 sec

Drive speed, raised or
extended

0.4 mph

40 ft/68 sec

0.65 km/h

12 m/68 sec

Drive speed, boom
above
125 ft / 38.1 m

0.1 mph

40 ft/270 sec

0.17 km/h

12 m/270 sec

Floor loading information

Tire load maximum

28,500 lbs

12,923 kg

Tire contact pressure

130 psi

9.13 kg/cm

2

896 kPa

Occupied floor pressure
(axles extended)

159 psf

778 kg/m

2

7.63 kPa

Occupied floor pressure
(axles retracted)

306 psf

1494 kg/m

2

14.65 kPa

Note: Floor loading information is approximate and does
not incorporate different option configurations. It should
be used only with adequate safety factors.

Continuous improvement of our products is a Genie
policy. Product specifications are subject to change
without notice or obligation.

«
...
72
73
74
75
76
...
»

Содержание SX-150














































































Отзывы:

Нет отзывов

Похожие инструкции для SX-150

Бренд: Genie Страницы: 36

Бренд: CTE Страницы: 144

Бренд: Genie Страницы: 183

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды