Genie SX-150 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 77

background image

Operator's Manual

Second Edition • Third Printing

Controls

30

SX-150 • SX-180

Part No. 1262335

20

Steer mode select switch with indicator lights

Move the steer
mode select switch
to choose steer
mode.
The indicator light
next to the current
steer mode will be
on.

21

Dual axis proportional control handle for jib
boom up/down and rotate left/right functions

Move the control handle
up and the jib boom will
raise. Move the control
handle down and the jib
boom will lower.

Move the control handle
to the left and the jib
boom will rotate left.
Move the control handle
to the right and the jib
boom will rotate right.

22

Drive select switch with indicator lights

Move the drive select
switch to choose drive
setting. The indicator
light next to the current
setting will be on.

Machine on incline
symbol: Low range
operation for inclines.

Machine on level
surface symbol: High
range operation for
maximum drive speed.

23

Single axis proportional control handle for
boom extend/retract function

Move the control handle
down and the boom will
extend. Move the control
handle up and the boom will
retract.

24

Axle extend/retract switch with indicator lights

Move the axle select
switch to choose an axle
setting. The axle extend
and retract indicator lights
will flash while the axles
are moving. The axle
extend indicator light will
stay on when the axles
are fully extended. The
axle retract indicator light
will stay on when the axles
are fully retracted.

«
...
30
31
32
33
34
...
»

Содержание SX-150














































































Отзывы:

Нет отзывов

Похожие инструкции для SX-150

Nussbaum UNI LIFT 6500

Бренд: ATT Страницы: 72

Бренд: TEUPEN Страницы: 312

Бренд: Torin Страницы: 31

Бренд: JLG Страницы: 202

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды