Genie S-100HD Скачать руководство пользователя страница 49

Страница: 49 / 55

First Edition • First Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1256222

S-100HD • S-120HD

Observe and Obey:

Only qualified riggers should rig the machine.

Only certified crane operators should lift the
machine and only in accordance with the
applicable crane regulations.

Be sure the crane capacity, loading surfaces
and straps or lines are sufficient to withstand
the machine weight. See the serial label for the
machine weight.

Lifting Instructions

Fully lower and retract the boom. Move the jib boom
(if equipped) parallel with the ground. Remove all
loose items on the machine.

Use the turntable rotation lock to secure the
turntable.

Determine the center of gravity of your machine
using the table and the picture on this page.

Attach the rigging only to the designated lifting
points on the machine. There are two lifting points
on the chassis and two on the turntable.

Adjust the rigging to prevent damage to the
machine and to keep the machine level.

Use a spreader bar to keep the rigging from
damaging the machine.

Center of gravity

X Axis

Y Axis

S-100HD

1.96 m

1.23 m

S-120HD

1.89 m

1.68 m

Содержание S-100HD
























































Результаты поиска

Содержание S-100HD

Отзывы:

Похожие инструкции для S-100HD

Бренды по названию

Популярные бренды

Genie S-100HD, Руководство оператора

Результаты поиска

Содержание S-100HD

Отзывы:

Похожие инструкции для S-100HD

Бренды по названию

Популярные бренды