Genie GS-2668DC Скачать руководство пользователя страница 4

Страница: 4 / 30

Genie GS-2668 DC & GS-3268 DC

Part No. 52546

Operator's Manual

First Edition • Seventh Printing

SAFETY RULES

Electrocution Hazards

This machine is not electrically insulated and will
not provide protection from contact with or
proximity to electrical current.

Maintain safe distances from electrical power lines
and apparatus in accordance with applicable
governmental regulations and the following chart.

Voltage

Minimum Safe

Phase to Phase

Approach Distance

Feet

Meters

0 to 300V

Avoid Contact

300V to 50KV

3.05

50KV to 200KV

4.60

200KV to 350KV

6.10

350KV to 500KV

7.62

500KV to 750KV

10.67

750KV to 1000KV

13.72

Allow for platform movement, electrical line sway or
sag and beware of strong or gusty winds.

Keep away from the machine if it contacts
energized power lines. Personnel on the ground or
in the platform must not touch or operate the
machine until energized power lines are shut off.

Do not operate the machine during lightning or
storms.

Do not use the machine as a ground for welding.

1250 lbs / 567 kg

Platform only
950 lbs / 431kg

Extension only
300 lbs / 136 kg

1000 lbs / 454 kg

Platform only
700 lbs / 318 kg

Extension only
300 lbs / 136 kg

Tip-over Hazards

Occupants and equipment shall not exceed the
maximum platform capacity or the maximum
capacity of the platform extension.

Maximum capacity - GS-2668DC

Platform retracted

1250 lbs

567 kg

Platform extended - Platform only

950 lbs

431 kg

Platform extended - Extension only 300 lbs

136 kg

Maximum occupants - ANSI and CSA

Maximum occupants - CE
Outdoor use

Indoor use only

Maximum capacity - GS-3268DC

Platform retracted

1000 lbs

454 kg

Platform extended - Platform only

700 lbs

318 kg

Platform extended - Extension only 300 lbs

136 kg

Maximum occupants - ANSI and CSA

Maximum occupants - CE
Outdoor use

Indoor use only

Содержание GS-2668DC































Результаты поиска

Содержание GS-2668DC

Отзывы:

Похожие инструкции для GS-2668DC

Бренды по названию

Популярные бренды

Genie GS-2668DC, Руководство оператора с информацией по обслуживанию

Результаты поиска

Содержание GS-2668DC

Отзывы:

Похожие инструкции для GS-2668DC

Бренды по названию

Популярные бренды