Genie GS-2668 RT Скачать руководство пользователя

Страница: 45 / 46

Operator's Manual

Fifth Edition · Second Printing

Part No. 133534

GS-2668 RT • GS-3268 RT

GS-3268 RT

Height, working maximum

11.8 m

Height, platform maximum

9.8 m

Height, stowed maximum,
Rails up

2.6 m

Height, stowed maximum,
Rails lowered

1.8 m

Height, stowed maximum,
Rails off

1.3 m

Height, guard rails

1.02 m

Width

1.73 m

Length, platform retracted

2.67 m

Length, platform retracted,
Models with outriggers

3.4 m

Length, platform extended

4.2 m

Maximum load capacity

454 kg

Maximum wind speed

12.5 m/s

Wheelbase

1.85 m

Turning radius (outside)

3.7 m

Turning radius (inside)

1.5 m

Ground clearance

21 cm

Weight

4149 kg

(Machine weights vary with option configurations. See
serial label for specific machine weight.)

Controls

Proportional

AC outlet in platform

Standard

Platform dimensions

Platform length x width

2.5 x 1.5 m

Platform extension length

1.5 m

Vibration does not exceed 2.5 m/s

Drive speeds

Stowed, maximum

6.1 km/h

Platform raised, maximum

0.8 km/h

12.2 m/54.6 sec

Maximum hydraulic pressure
(functions)

241.3 bar

Tires size

26 x 12 x 380

Maximum slope rating,
stowed position

35%

(19°)

Maximum side slope rating,
stowed position

35%

(19°)

Note: Slope rating is subject to ground conditions and
adequate traction.

Floor loading information

Tire load, maximum

1485 kg

Outrigger load, maximum

1485 kg

Tire contact pressure

5.73 kg/cm2

561 kPa

Outrigger contact pressure

2.93 kg/cm2

287 kPa

Occupied floor pressure

1082 kg/m2

10.62 kPa

Note: Floor loading information is approximate and
does not incorporate different option configurations. It
should be used only with adequate safety factors.

Airborne noise emissions

Sound pressure level at ground workstation

83 dBa

Sound pressure level at platform workstation

79 dBa

Guaranteed sound power level

102 dBa

Specifications

Содержание GS-2668 RT















































Результаты поиска

Содержание GS-2668 RT

Отзывы:

Похожие инструкции для GS-2668 RT

Бренды по названию

Популярные бренды

Genie GS-2668 RT, Руководство оператора

Результаты поиска

Содержание GS-2668 RT

Отзывы:

Похожие инструкции для GS-2668 RT

Бренды по названию

Популярные бренды