background image

5

English

SERVICE

• 

Have your power tool serviced by a qualified repair person using 

only identical 

replacement parts. 

This will ensure that the safety of the power tool is maintained. 

• 

Service your power tool periodically

.  

When cleaning a tool, be careful not to disassemble any 

portion of the tool since internal wires may be misplaced or pinched.

SAVE THESE INSTRUCTIONS

EXTENSION COrDS

Grounded tools require a three wire extension cord

.

 

 Double insulated tools can 

use either a two or three wire extension cord.  As the distance from the power supply outlet increases, you must 
use a heavier gauge extension cord.  using extension cords with inadequately sized wire causes a serious drop 
in voltage, resulting in loss of power and possible tool damage.  Refer to the table shown below to determine the 
required minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord.  for example: a 14-gauge cord 
can carry a higher current than a 16-gauge cord.  When using more than one extension cord to make up the total 
length, be sure each cord contains at least the minimum wire size required.  If you are using one extension cord 
for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire 
size.

Guidelines for Using Extension Cords

•  If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to 

indicate that it is acceptable for outdoor use.

•  Be sure your extension cord is properly wired and in good electrical condition.  Always replace a damaged 

extension cord or have it repaired by a qualified person before using it.

•  Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

SPECIFIC SAFETY rULES FOr COrDLESS IMPACT 
DrIVErS

 

 

WArNING:

 

 

DO NOT LET COMFOrT Or FAMILIArITY WITH PrODUCT (GAINED 

FrOM rEPEATED USE) rEPLACE STrICT ADHErENCE TO PrODUCT SAFETY rULES. If 
you use this tool unsafe or incorrectly, you can suffer serious personal injury! 

•  

Hold the tool by insulated gripping surfaces when performing an operation

 

where the tool may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool 
“live” and shock the operator.

•  

Do not leave the tool running

. Operate the tool only when hand-held.

• 

Be aware that this tool is always in an operating condition

, because it does not have 

to be plugged into an electric outlet.

•  

When operating the tool from an elevated position

, be aware of people or things 

beneath you.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate 

Amperes  

(At Full Load)

Extension Cord Length

25 Feet

50 Feet

75 Feet

100 Feet

150 Feet

200 Feet

0–2.0

18

18

18

18

16

16

2.1–3.4

18

18

18

16

14

14

3.5–5.0

18

18

16

14

12

12

5.1–7.0

18

16

14

12

12

10

7.1–12.0

18

14

12

10

8

8

12.1–16.0

14

12

10

10

8

6

16.1–20.0

12

10

8

8

6

6

Содержание GLID20A












Отзывы: