AF500 AIR-SCRUB-R
®
Portable HEPA Air Filter
FORM GOM24101701US, VERSION 1.0
English-EN
8
FIGURE 8
FIGURE 9
FIGURE 10
5.
Turn AIR-SCRUB-R ON/OFF switch to OFF position and disconnect
power cord from power source. Refer to FIGURE 7
6.
Depending on location/access of area to be filtered, install accessory
ducting as necessary per procedures in INSTALLING & REMOVING
PRIMARY & OUTLET ACCESSORY DUCTING in MACHINE SET-UP
section of this manual.
7.
Position ducting for optimal air flow. Avoid extremely sharp or more than
two 90
˚
bends over length of duct.
8.
Inspect power cord BEFORE use for damage, cuts, abrasions and/or
electrical tape.
9.
Connect AIR-SCRUB-R power cord to power source.
IMPORTANT:
Due to integral GFCI receptacle in unit, power cord of unit must
be plugged directly into wall outlet. DO NOT use any extension cords.
IMPORTANT:
If GFCI detects a ground fault, short circuit or overload, GFCI
will interrupt power to unit. If this occurs, turn AIR-SCRUB-R ON/OFF switch to
OFF position immediately and disconnect power cord from power source.
Check for potential causes of power surge such as standing water, frayed
power cord, power source circuitry. Once cause has been determined and
addressed, refer to STEP 4 this section of manual to “reset” GFCI.
NOTE:
Up to 4 AIR-SCRUB-Rs can be daisy chained together for simultaneous
operation by plugging power cord of one unit into the GFCI outlet of the next
unit in line. Last unit in the chain is connected to the power source. Total
amperage of all devices plugged into GFCI receptacle must not exceed 10
amps.
10. Turn AIR-SCRUB-R ON/OFF switch to ON position. Monitor airflow for
any obstructions. Refer to FIGURE 8
IMPORTANT:
Motor will restart if power is lost then comes back on. There is
no automatic shut off feature on the AIR-SCRUB-R.
11. Monitor change filter indicator light throughout operation. When light
indicates filter changing is necessary, examine and replace pre-filter
and/or HEPA filter as necessary per REPLACING PRE-FILTER &
SECONDARY HEPA FILTER of MAINTENANCE INSTRUCTIONS
section in this manual. FIGURE 11
WARNING
•
For maximum protection against a fault, always configure
power cord to be plugged into power source receptacle.
•
Configurations with GFCI placed between AIR-SCRUB-R
and power source will not provide maximum protection
against potential fault.
WARNING
•
BEFORE use, inspect power cord for proper structural
integrity.
•
DO NOT use cord with worn or cut outer jacket material or
repaired with electrical tape.
•
Use of cords with improper structural integrity can result
in property damage and/or personal injury.
WARNING
•
DO NOT abuse the power cord. Never use power cord to
move AIR-SCRUB-R or pull plug from wall receptacle or
unit GFCI receptacle. Damage to cord and GFCI can
result.
•
A damaged cord increases the risk of an electric shock.
WARNING
•
Keep power cord free and clear of machine and
accessory ducting, heat, oil, sharp edges and moving
parts.
•
In event power cord becomes entangled about
AIR-SCRUB-R and/or operator turn machine OFF
immediately.
•
Determine power cord/GFCI receptacle are in proper
condition to continue operation.
•
In event of damage, replace with factory approved
component only.
DANGER
•
DO NOT modify, bypass or disable AIR-SCRUB-R ON/OFF
switch.
•
DO NOT operate machine if machine ON/OFF switch is not
functioning properly
•
Such configuration will not allow operator to quickly stop
AIR-SCRUB-R in event of an emergency, prevent
unexpected machine start-up, loss of control and can
result in property damage and/or personal injury.
