General Pipe Cleaners JM-1450, Руководство по эксплуатации

Страница: 4 / 35

Jet-Set JM-1450™
3
GENERAL SAFETY RULES
WORK AREA SAFETY
1. All installations must comply with local codes. Contact your
electrician, plumber, utility company or the selling distributor for
specific details. To comply with the National Electrical code (NFPA
70) and provide additional protection from risk of electric shock,
the machines are equipped with a UL approved ground fault circuit
interrupter (GFCI) power cord.
2. Risk of explosion. Do not spray flammable liquids or operate
in an area where flammable or explosive materials are used
or stored.
Power tools create sparks which may ignite dust and
fumes.
3. Keep bystanders, children, and visitors away while operating
machine.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Grounded tools must be plugged into an outlet, properly in-
stalled and grounded in accordance with all codes and ordi-
nances. Never remove the grounding prong or modify the
plug in any way. Do not use any adapter plugs. Check with a
qualified electrician if you are in doubt as to whether the out-
let is properly grounded. If the tool should electrically malfunc-
tion or break down, grounding provides a low resistance path to
carry electricity away from the user.
2. Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk
of electric shock if your body is grounded.
3. Do not expose power tools to rain or wet conditions . Water
entering a power tool will increase the risk of electric shock.
4. When operating a power tool outside use an outdoor exten-
sion cord marked “W - A” or “W”. These cords are rated for out-
door use and reduce the risk of electric shock.
5. Test the Ground Fault Circuit Interrupter (GFCI) provided with
the power cord to insure it is operating correctly before oper-
ating machine. Machine must have a properly functioning ground
fault circuit interrupter on the power cord. GFCI reduces the risk of
electric shock.
6. Extension cords are not recommended unless they are
plugged into a Ground Fault Circuit Interrupter (GFCI) found
in circuit boxes or outlet receptacles. The GFCI on the ma-
chine power cord will not prevent electric shock from the extension
cords.
7. Only use proper three-wire extension cords in good condition
of no more than 50 ft. in length which have three-prong
grounding plugs and three-pole receptacles which accept the
tools plug. Use of damaged, inferior, or other extension cords will
not ground the tool, increases the risk of damage to the machine,
electric shock, bodily injury or death.
8. Keep all electric connections dry and off the ground . Reduces
the risk of electric shock.
9. DO NOT touch plugs or tools with wet hands. Reduces the risk
of electric shock.
GROUND FAULT CIRCUIT INTERRUPTER (GFCI)
Your machine is equipped with a ground fault circuit interrupter, which
protects you against shock if a short circuit should occur. Check that
receptacle is properly grounded. Test the GFCI before each use.
1. Plug into 120-volt receptacle.
2. Push test button. Indicator light will go out and power to machine
should cut off.
3. If light does not go out when test button is pushed, DO NOT USE
THE MACHINE until proper repairs can be made.
4. To restore power after test, push reset button. With the reset but-
ton depressed, if the machine doesn't start, stops while running, or
if the operator experiences a mild shock, DO NOT USE THE MA-
CHINE! Tag the machine out of service and take it to a motor
repair center or return it to the factory for repairs.
PERSONAL SAFETY
1. High pressure developed by jet machines will cause personal
injury. Water spray should not be pointed at any person. High
pressure spray can result in serious injury. If fluid seems to have
penetrated the skin, seek emergency medical attention at once.
2. Grip jet hose or spray wand securely with both hands before
starting the machine.
Failure to do so could result in injury from a
whipping hose or wand.
3. Always wear eye protection and rubber gloves. Safety equip-
ment, eye safety devices, non-skid safety shoes and protective
clothing must be worn when using this equipment.
4. Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or medication. A mo-
ment of inattention while operating power tools may result in seri-
ous personal injury.
5. Dress properly. Do not wear loose clothing or jewelry. Con-
tain long hair. Keep your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long hair can be caught
in moving parts.
SERVICE
1. Tool service must only be performed by qualified service
personnel. Service or maintenance performed by untrained per-
sonnel could result in injury and damage to the equipment.
2. When servicing tool, use only identical replacement parts.
Follow instructions in maintenance section of this manual.
Use of unauthorized parts or failure to follow maintenance instruc-
tions may cause injury or damage to equipment.
JET SAFETY
1. Do not operate jet above rate pressure or above 140 degrees
(rated water temperature). Operating jet above rate specifica-
tions risks damage to the pump and related components, and will
void the warranty.
2. Do not operate jet with the output valve in the off position for
extensive periods of time.
This will cause the water to overheat
and damage the pump.
3. Never run pump without water in it. Operating the machine
without water will cause the pump to fail and void the warranty.
WARNING
Read and understand all instructions. Failure to follow all in-
structions listed below may result in electric shock, fire, and/or
serious injury.
SAVE THESE INSTRUCTIONS!