General International DP2002 Скачать руководство пользователя страница 14

Страница: 14 / 44

ENGLISH

of the base and the table.

3. Using a 4 mm hex (Allen) key, fasten the head assembly in place by

tightening the head lock set screws (dd, fig 3) in the right side of the

head casting.

Screw the three feed handles (M, fig 2 & 3) into the the threaded

holes in the hub. Instead of using the knobs for leverage and possibly

stripping them, use a wrench on the flats at the threaded ends of the

handles to tighten, but take care to fasten them only hand tight.

5. Install an M5 x 12 pan head screw from the inside of the pulley cover

through the hole and attach the knob (aa, fig 3) to the outside.

NOTE:

One or two of the feed handles may have to be temporarily

removed in future if a job involves an unusually-shaped workpiece that

interferes with handle rotation.

CHUCK

Clean out the tapered hole in the chuck (K, fig 2 & 3), removing any

grease, anti-rust coating or dirt you find.

2. Clean grease, coating and dirt from the JT33 tapered spindle tip with a

clean cloth.

Open the chuck's jaws as far as they will go so they are fully retracted

into the chuck.

4. Push the chuck up on the spindle as far as possible. Lightly tap the

lower end of the chuck with a piece of wood to ensure the chuck fits

tightly on the spindle.

5. To remove the chuck, see Maintenance.
6.

Clamp the chuck safety guard (J, fig 3) around the lower exposed part of

the quill tube. Do not over-tighten.

LASER BATTERIES

Locate the laser switch (T, fig 3) on the left side of the head assembly.

Press the tab located below the laser switch (fig 6) and raise the cover.

3. Insert 2 "AA" batteries, oriented in the directions indicated.
4. Close the switch cover.

CAUTION:

Remove these batteries from the compartment when the

tool is to be stored without use for more than a few days. If left in, the

batteries may leak and damage the laser device. Damage from leaking

batteries is not covered under the warranty.

ADJUSTMENTS

WARNING!

To reduce the risk of injury, keep pulley cover in place and

in proper working order when operating.

SPEED AND BELT TENSION

ADJUSTMENT

1. Open the belt & pulley cover (

X, fig 2 & 3

)

2. Consult the belt position / speed diagram.

fig 6

rpm: 570 tr/min

spindle

broche

motor

moteur

rpm: 900 tr/min

spindle

broche

motor

moteur

rpm: 1390 tr/min

spindle

broche

motor

moteur

rpm: 2050 tr/min

spindle

broche

motor

moteur

rpm: 3050 tr/min

spindle

broche

motor

moteur

DP2002 belt spindle label

100 x 40 mm R=2

Содержание DP2002













































Результаты поиска

Содержание DP2002

Отзывы:

General International DP2002, Руководство по установке и эксплуатации, Страница: 14 / 44

Результаты поиска

Содержание DP2002

Отзывы: