background image

INSTALLING THE BELT TABLE

1.  Install sanding belt table using the carriage 

 

 

bolt, flat washer, and ratchet lever as shown. 

Note:  

 

Make sure to position the trunnion over the alignment  

 

screw as shown, A. 

Tip: using an 11 mm wrench, tighten the ratchet lever 

onto the carriage bolt at least a few turns until enough 

threads are engaged to allow tightening the lever by 

hand.

Align/level the table by hand and then using a 10 mm 

wrench and phillips head screwdriver tighten the table 

mounting brackets.

CARRIAGE 

BOLT

A

10

The two supplied 1 1/2” diameter dust outlets allow for 

connection to a dust collector (not included). Be sure to 

use appropriate sized hose and fittings (not included) 

and check that all connections are sealed tightly to 

help minimize airborne dust.
If you do not already own a dust collection system con- 

sider contacting your 

General® International

 distribu-

tor for information on our complete line of dust collec-

tion systems and accessories or visit our Web Site at 

www.general.ca

.

ALWAYS TURN ON THE DUST COLLECTOR BEFORE STARTING THE SANDER AND ALWAYS STOP THE SANDER BEFORE TURNING OFF 

THE DUST COLLECTOR.

CONNECTING TO A DUST COLLECTOR

DO NOT OPERATE THIS SANDER WITHOUT AN ADEQUATE DUST COLLECTION SYSTEM PROPERLY INSTALLED AND RUNNING. OPERAT-

ING THIS SANDER WITHOUT ADEQUATE DUST COLLECTION CAN LEAD TO EQUIPMENT MALFUNCTION OR DANGEROUS SITUATIONS 

FOR THE OPERATOR OR OTHER INDIVIDUALS IN THE WORKSHOP.

Using the thumbscrew and rubber washer, install the 

see-through belt guard as shown. 

Note: Do not overtight-

en the thumbscrew.

INSTALLING BELT GUARD

Install the dust chute to the bottom of the disc with a 

phillips head screw driver, as shown using the 4 sup-

plied screws.

INSTALLING THE DUST CHUTE

Содержание 15-142 M1




















Отзывы: