Generac Power Systems MLTS Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 48

Generac Power Systems MLTS Скачать руководство пользователя страница 24

20

Owner’s Manual for Mobile Light Tower

Operation

6.

See Detail E. Rotate each jack handle clockwise to
start  leveling  the  trailer. Adjust  all  three  jacks  by
rotating their handles clockwise until they are firmly
in  contact  with  the  ground.  Continue  until  the
wheels  are  approximately  1  in  (2.5  cm)  off  the
ground (G).

7.

Before raising the mast, it may be necessary to
adjust the lamps. The lamps may be adjusted up,
down, left, or right by aiming them in the desired
direction.

Raising the Mast—Manual Winch

1.

Set up and level the unit. See

Light Tower Setup

.

2.

See

Figure 3-2

. Inspect the mast cables for

excessive wear or damage. Verify the cables are
properly centered in each pulley (A). Inspect the
electrical cord for damage.

3.

Rotate the mast by loosening the mast rotation
knob (C) at the bottom of the mast. Turn the mast
until the lights face in the desired direction. Tighten

the mast rotation knob to secure the mast in
position.

4.

Using both hands, rotate the winch (B) to slowly
extend the mast. Verify the coiled electrical cord is
extending at the top sections of the mast. Stop
extending the mast when the colored mark (D) on
the second mast section is visible as seen in Detail
D.

Figure 3-2. Pulley Locations—Manual Winch

IMPORTANT NOTE: Contact a GMASD immediately
if the mast hangs up or the winch cable develops
slack.

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit
before raising the mast. Keep the outriggers extended while
the mast is up. Failure to do so could cause the unit to tip
and fall and could result in death or serious injury.

WARNING

Tipping hazard. Do not extend the mast beyond the
colored mark on the second mast section. The unit
can become unstable and tip or fall, causing injury.

(000262)

WARNING

Personal Injury. Stop immediately if the mast hangs
up or the winch cable develops slack. Excess slack
could cause the mast to collapse, resulting in personal
injury or equipment damage.

(000265)

(000279)

Personal injury or equipment damage. Do not raise
or lower the mast while the unit is operating.
Doing so can break the lenses and cause the
lamps to shatter.

WARNING

DETAIL D

STOP

008709

A

D

B

C

«
...
22
23
24
25
26
...
»

Содержание MLTS

















































Отзывы:

Нет отзывов