Generac Power Systems MLTS Скачать руководство пользователя страница 2

ii

Use this page to record important information about your light tower

Record the information found on your unit data label on
this  page.  See  unit  serial  number  location  (

Unit Serial

Number Locations

).  The  label  plate  is  affixed  to  the

inside partition, to the left of the control panel console. 
Engine  and  generator  serial  numbers  are  located  on
separate data plates affixed to the engine and generator.
When  contacting  a  Generac  Mobile Authorized  Service
Dealer  (GMASD)  about  parts  and  service,  supply  the
complete model number and serial number of the unit.

Operation and Maintenance:

 Proper maintenance and

care  of  the  light  tower  ensures  a  minimum  number  of
problems and keeps operating expenses at a minimum. It
is  the  operator’s  responsibility  to  perform  all  safety
checks, to verify that all maintenance for safe operation is
performed promptly, and to have the equipment checked
periodically by a GMASD. Normal maintenance, service
and  replacement  of  parts  are  the  responsibility  of  the
owner  or  operator  and,  as  such,  are  not  considered
defects  in  materials  or workmanship  within the terms of
the warranty. Individual operating habits and usage may
contribute  to  the  need  for  additional  maintenance  or
service.

Unit Model No.

Unit Serial No.

Engine Model No.

Engine Serial No.

Generator Model No.

Generator Serial No.

(000394)

WARNING

Breathing diesel engine exhaust exposes you 
to chemicals known to the State of California
to cause cancer and birth defects or other 
reproductive harm.
• Always start and operate the engine in a 
  well-ventilated area.
• If in an enclosed area, vent the exhaust to 
  the outside.
• Do not modify or tamper with the exhaust 
  system.
• Do not idle the engine except as necessary.
For more information go to 

www.P65Warnings.ca.gov/diesel.

(000393a)

WARNING

CANCER AND REPRODUCTIVE HARM

www.P65Warnings.ca.gov.

Содержание MLTS

















































Отзывы: