Generac Power Systems MLTS Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 48

Generac Power Systems MLTS Скачать руководство пользователя страница 23

Owner’s Manual for Mobile Light Tower

19

Section 3: Operation

Light Tower Setup

Figure 3-1. Setup Components

1.

For maximum light coverage, position the unit at
ground level or in a spot higher than the area being
illuminated by the lamps.

NOTE:

For mast height, see

Unit Dimensions

.

2.

Place the unit on firm ground that is relatively flat
(less than 5° slope), and then block the wheels to
prohibit movement. This will make it easier to level
the unit.

3.

See

Figure 3-1

. Pull the locking pin (A) on the

tongue jack (E) and rotate the jack 90°. Reinstall
the locking pin. Rotate the jack handle clockwise to
raise the trailer tongue off the towing vehicle.

4.

A grounding stud (B) is located on the rear frame of
the trailer near the left side outrigger. For ground-
ing requirements, follow local, state, or National
Electrical Code (NEC) guidelines.

5.

See  Details  C–D.  Pull  the  locking  pins (C)  on  the
outriggers (D) and pull each outrigger out until the
spring  loaded  locking  pin  snaps  back  into  place.
Pull the locking pin on each outrigger jack (F) and
rotate  each  jack  180°  so  the  jack  pad  is  facing
down. Reinstall the locking pin.

1”

DETAIL B

DETAIL C

DETAIL E

DETAIL D

A

E

G

B

F

D

C

008708

(000260a)

High Voltage. Verify area above unit is clear
of overhead wires and obstructions. Contact
with high-voltage power lines will result in
death or serious injury.

DANGER

WARNING

(000297)

> 60 mph

Do not set up the unit if high winds
are expected. High winds can cause the
unit to tip or fall, causing severe injury
or machine damage.

«
...
21
22
23
24
25
...
»

Содержание MLTS

















































Отзывы:

Нет отзывов