manualshive.com logo in svg

Generac Power Systems MAGNUM MMG100D, Руководство пользователя, Страница: 21 / 48

Поделиться
Скачать
Generac Power Systems MAGNUM MMG100D Скачать руководство пользователя страница 21

Owner’s Manual for Generator

17

Operation

Transfer Switch

Installation should be in compliance with the National
Electrical Code (NEC), state and local regulations.
Before any connections are attempted, verify the main
circuit breaker and the Control Power switch are in the
OFF (O) position and that the negative (-) battery cable
has been disconnected from the battery.
Installation of such devices must be performed by
following all directions supplied by the manufacturer of
the switch. If attaching the unit to a power supply
normally serviced by a utility company, notify the utility
company and check state and local regulations.
Familiarize yourself with all instructions and warning
labels supplied with the switch.
When the unit is used as a standby power supply, it must
be equipped with a transfer switch which isolates it from
the utility’s distribution system. A transfer switch is
designed to transfer electrical loads from the normal
power source (utility) to the emergency power source
(generator) when normal voltage falls below a prescribed
level. The transfer switch automatically returns the load
back to the normal source when power is restored back
to operating levels.

Figure 3-3. Transfer Switch Operation

Derating for Altitude

All units are subject to derating for altitude; this will
reduce the available power for operating tools and
accessories connected to the receptacles. Typical
reductions in performance are 5% per 1,000 ft above
10,000 ft (3048 m) of elevation.

(000190)

DANGER

Loss of life. Property damage. Installation must always
comply with applicable codes, standards, laws and  
regulations. Failure to do so will result in death  
or serious injury.  

(000237)

DANGER

Electrical backfeed. Use only approved switchgear to 
isolate generator from the normal power source.
Failure to do so will result in death, serious injury, 
and equipment damage.

(000155)

WARNING

Only a trained and licensed electrician should perform
wiring and connections to unit. Failure to follow proper
installation requirements could result in death, serious
injury, and damage to equipment or property.

(000226)

Phase rotation between transfer switch and 
power lines must be compatible. Incompatible 
phase rotation could result in equipment 
damage, death or serious injury.

 

WARNING

A

Incoming Utility Power

B

Emergency Distribution Panel (Generator 
Power)

C

Main Distribution Panel (Utility Power)

D

Transfer Switch

E

Power From Generator

F

Utility Meter

WHITE

Incoming Utility Power

GRAY

Normal Utility Power Circuit

BLACK

Emergency Generator Power Circuit

A

B

C

D

E

F

Содержание MAGNUM MMG100D

















































Отзывы:

Нет отзывов