manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 32

Operation

28

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

is extending at the top sections of the mast. Stop
extending the mast when the colored mark (C) on
the second mast section is visible as seen in Detail
C.

IMPORTANT NOTE: A limit switch on the main mast
section will disconnect power to the electric winch to
prevent overextending the mast.

IMPORTANT  NOTE:  Contact  a  GMP  ASD  immedi-
ately if the mast hangs up or the winch cable devel-
ops slack.

Raising the Mast—Power Zone-

DLA (If Equipped)

NOTE: 

Units  with  the  Power  Zone-DLA  do  not  have  a

mast switch for the electric winch.

1.

Set up and level the unit. See 

Light Tower Setup

.

2.

Turn the control power switch to on.

3.

See 

Figure 2

 and 

Figure 3-5

. Press the up/down

arrows (A) until the mast screen is shown. 

Figure 3-4. Power Zone Controller

Figure 3-5. Raising the Mast Screen

4.

Press  the  SELECT  button  (B);  the  UP/DOWN  on
the display will begin to flash. Press the arrows as
needed until the mast is at the desired height. See

Figure 3-3

.  Do  not  extend  past  the  colored  mark

(C).

5.

Press  SELECT  again  to  exit  the  mast  control
screen.

IMPORTANT  NOTE:  Contact  a  GMP  ASD  immedi-
ately if the mast hangs up or the winch cable devel-
ops slack.

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit 
before raising the mast. Keep the outriggers extended while 
the mast is up. Failure to do so could cause the unit to tip 
and fall and could result in death or serious injury. 

WARNING

Tipping hazard. Do not extend the mast beyond the 
colored mark on the second mast section. The unit 
can become unstable and tip or fall, causing injury.

(000262)

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

(000279)

Personal injury or equipment damage. Do not raise 
or lower the mast while the unit is operating. 
Doing so can break the lenses and cause the 
lamps to shatter.

WARNING

Select

002353

A

B

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды