manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 31

Operation

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

27

Raising the Mast—Electric Winch 

(If Equipped)

1.

Set up and level the unit. See 

Light Tower Setup

.

Figure 3-3. Switch & Pulley Locations—Electric 

Winch

2.

See 

Figure 3-3

.  Inspect  the  mast  cables  for

excessive  wear  or  damage.  Verify  the  cables  are
properly  centered  in  each  pulley  (A).  Inspect  the
electrical cord for damage.

3.

Rotate  the  mast  by  loosening  the  mast  rotation
knob at the bottom of the mast (D). Turn the mast
until the lights face in the desired direction. Tighten
the  mast  rotation  knob  to  secure  the  mast  in
position.

NOTE: 

On  Key  Switch  models,  key  must  be  in

RUN position to operate electric winch.

4.

Press and hold the winch control switch (Detail B)
upward to telescope the mast to the desired height.
While doing so, verify that the coiled electrical cord

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit 
before raising the mast. Keep the outriggers extended while 
the mast is up. Failure to do so could cause the unit to tip 
and fall and could result in death or serious injury. 

WARNING

Tipping hazard. Do not extend the mast beyond the 
colored mark on the second mast section. The unit 
can become unstable and tip or fall, causing injury.

(000262)

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

(000279)

Personal injury or equipment damage. Do not raise 
or lower the mast while the unit is operating. 
Doing so can break the lenses and cause the 
lamps to shatter.

WARNING

DETAIL C

STOP

DETAIL B

008710

A

D

C

B

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды