manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 29

Operation

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

25

Section 3: Operation

Light Tower Setup

Figure 3-1. Set Up Outriggers and Jacks

1.

For  maximum  light  coverage,  position  the  unit  at
ground level or in a spot higher than the area being
illuminated by the lamps.

NOTE: 

The mast extends up to 23 ft (7 m).

2.

Place the unit on firm ground that is relatively flat
(less than 5° slope), and then block the wheels to
prohibit movement. This will make it easier to level
the unit.

3.

See 

Figure 3-1

.  Pull  the  locking  pin  (A)  on  the

tongue  jack  (E)  and  rotate  the  jack  90°.  Reinstall
the locking pin. Rotate the jack handle clockwise to
raise the trailer tongue off the towing vehicle.

4.

A grounding stud (B) is located on the rear frame of
the trailer near the left side outrigger. For ground-
ing  requirements,  follow  local,  state,  or  National
Electrical Code (NEC) guidelines.

5.

See Details C—D. Pull the locking pins (C) on the
outriggers (D) and pull each outrigger out until the
spring  loaded  locking  pin  snaps  back  into  place.
Pull the locking pin on each outrigger jack (F) and
rotate  each  jack  180°  so  the  jack  pad  is  facing
down. Reinstall the locking pin.

1”

DETAIL B

DETAIL C

DETAIL E

DETAIL D

A

E

G

B

F

D

C

008708

(000260a)

High Voltage. Verify area above unit is clear 
of overhead wires and obstructions. Contact 
with high-voltage power lines will result in 
death or serious injury.

DANGER

WARNING

(000297)

> 60 mph

> 60 mph

Do not set up the unit if high winds 
are expected. High winds can cause the 
unit to tip or fall, causing severe injury 
or machine damage.

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды