Generac Power Systems 1040-0 Скачать руководство пользователя

Страница: 16 / 22

TROUBLESHOOTING POINTS

Generac 2000PSI High Pressure Washer

GENER

H i g h P r e s s u r e W a s h e r

Problem

Cause

Correction

Pump has following problems:

1. Nozzle in low pressure mode.

1. Pull nozzle backward for high

failure to produce pressure, erratic

pressure mode.

pressure, chattering, loss of pressure,

2. Water inlet is blocked.

2. Clear inlet

low water volume.

3. Inadequate water supply

3. Provide adequate water flow.

4. Inlet hose is kinked or leaking

4. Straighten inlet hose, patch leak.

5. Clogged inlet hose strainer.

5. Check and clean inlet hose

strainer.

6. Water supply is over 140°F.

6. Provide cooler water supply.

7. Outlet hose is blocked or leaks.

7. Clear blocks in outlet hose.

8. Gun leaks.

8. Replace gun.

9. Nozzle is obstructed.

9. Clear nozzle.

10. Pump is faulty.

10. Contact Generac service facility.

Detergent fails to mix with spray.

1. Detergent line is not submerged.

1. Insert chemical line into deter

gent.

2. Chemical filter is clogged.

2. Clean or replace filter/detergent

line.

3. Nozzle is in high pressure mode.

3. Push nozzle forward for

low pressure mode.

Engine runs good at no-load but bogs

Engine speed is too slow.

Move throttle control to FAST .

when load is added.

position. If engine still bogs down

contact Generac service facility.

Содержание 1040-0























Результаты поиска

Содержание 1040-0

Отзывы:

Похожие инструкции для 1040-0

Бренды по названию

Популярные бренды

Generac Power Systems 1040-0, Руководство пользователя

Результаты поиска

Содержание 1040-0

Отзывы:

Похожие инструкции для 1040-0

Бренды по названию

Популярные бренды