Generac Portable Products 1294-0 Скачать руководство пользователя страница 2

Generac Portable Products 2200 PSI High Pressure Washer

2

CAUTION!

Always disconnect spark plug

wire and place wire where it cannot contact

spark plug to prevent accidental starting when

setting up, transporting, adjusting or making

repairs to your high pressure washer.

• Engine exhaust gases contain DEADLY carbon

monoxide gas. This dangerous gas, if breathed in

sufficient concentrations, can cause

unconsciousness or even death. Operate this

equipment only in the open air where adequate

ventilation is available.

• Gasoline is highly FLAMMABLE and its vapors are

EXPLOSIVE. Do not permit smoking, open flames,

sparks or heat in the vicinity while handling

gasoline. Avoid spilling gasoline on a hot engine.

Allow unit to cool for 2 minutes before refueling.

Comply with all laws regulating storage and

handling of gasoline.

• Locate this pressure washer in areas away from

combustible materials, combustible fumes or dust.

• The high pressure equipment is designed to be

used with Generac authorized parts only. If you use

this equipment with parts that do not comply with

minimum specifications, the user assumes all risks

and liabilities.

• Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting or poisoning. The harmful elements may

cause property damage or severe injury.

• Do not allow CHILDREN to operate the Pressure

Washer at any time.

• Operate engine only at governed speed. Running

the engine at excessive speeds increases the

hazard of personal injury. Do not tamper with parts

which may increase or decrease the governed

speed.

• Do not wear loose clothing, jewelry or anything that

may be caught in the starter or other rotating parts.

• Before starting the Pressure Washer in cold

weather, check all parts of the equipment and be

sure ice has not formed there.

• Units with broken or missing parts, or without

protective housing or covers should NEVER be

operated.

• The muffler and air cleaner must be installed and in

good condition before operating the Pressure

Washer. These components act as spark arrestors

if the engine backfires.

• Check the fuel system for leaks or signs of

deterioration such as chafed or spongy hose, loose

or missing clamps or damaged tank or cap. Correct

all defects before operating the Pressure Washer.

• Do not spray flammable liquids.
• Never aim the gun at people, animals or plants.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects, or other reproductive harm.

WARNING:

IMPORTANT! — SAFETY RULES — IMPORTANT!

Save for future reference

Содержание 1294-0





















Отзывы: