Generac Mobile MMG35DF4 Скачать руководство пользователя | Manualshive

Страница: 22 / 60

background image

18

Owner’s Manual for Mobile Generator

General Information

(A) Navigation Buttons

See

Figure 2-7

. Used to navigate the operator pages.

Figure 2-7. Navigation Buttons

Navigate the operator pages as follows.

(B) Controller Screen

The controller screen displays various operational data for
unit monitoring, diagnosing, and troubleshooting. See

Operator Pages

for more information.

(C) Indicator LEDs

See

Figure 2-8

. Each LED indicates a condition that

impedes normal unit function.

Figure 2-8. Indicator LEDs

If an indicator LED is illuminated, resolve the condition to
restore normal unit function, as described in table below.

NOTE:

When a condition is resolved, the corresponding

indicator LED switches off.

NOTE:

If unable to resolve a condition as recommended,

contact a GMASD.

(D) Transfer to Generator Button

Only applies to MANUAL mode.
Controls operation of generator load switch, when the
generator is available.

NOTE:

In units equipped with a manual breaker, limited

function is available.
Status is indicated by the Close Generator LED.

(E) Close Generator LED

•

When illuminated, cam locks and lugs are enabled.

•

When not illuminated, cam locks and lugs are
disabled.

(F) Engine Start Button

When STOP/RESET mode is active, the Engine Start
button switches on the engine ECU but does not start the
engine. Uses in this context are to check status of the
CAN communication and to prime the engine.
When MANUAL mode is active, the Engine Start button
starts the generator.

NOTE:

In AUTO or STOP mode, the Engine Start button

activates the ECU.

(G) Alarm Mute and Lamp Test Button

Stops the audible alarm and illuminates functional
controller LEDs.
To test the LEDs, press and hold button. All LEDs
illuminate. When button is released, the LEDs switch off.

NOTE:

If an LED does not illuminate when button is

pushed, the LED is not functioning.

(H) AUTO Mode LED

•

When illuminated, AUTO mode is active.

•

When not illuminated, AUTO mode is not active.

(I) AUTO Mode Button

Switches the mode to AUTO. See

Controller Modes

for

important guidelines.
Status is indicated by the AUTO Mode LED.

(J) PAS valve test switch LED (if equipped)

When illuminated, PAS test is in progress.

►

View next

◄

View previous

▲

Scroll up current

▼

Scroll down current



Select highlighted item

A

Low Load

indicator LED.

•

Indicates genset has operated at less than 30%
capacity for more than 15 minutes.

•

Resolve by increasing electrical load. If unable
to operate genset at more than 30% load, use a
smaller generator.

B

Lug Door Open

indicator LED.

•

Indicates lug-box door is open.

•

Resolve by closing lug-box door. If condition
remains unresolved, inspect lug-box door safety
switch for proper operation.

010418

010419

A

B

C

D

C

Emergency Stop

indicator LED.

•

Indicates Emergency Stop switch is active
(pushed in).

•

Resolve by deactivating (pulling out) Emergency
Stop switch.

D

Shutdown

indicator LED.

•

Indicates a shutdown alarm is present.

•

Resolve by resolving shutdown condition.

«
...
20
21
22
23
24
...
»

Содержание MMG35DF4





























































Отзывы:

Нет отзывов

Похожие инструкции для MMG35DF4

Бренд: Lantronix Страницы: 142

Бренд: Control Techniques Страницы: 56

Бренд: Orbis Страницы: 2

Бренд: Optical Systems Страницы: 2

Бренд: C4i Страницы: 9

Бренд: B&B Electronics Страницы: 53

L.O.C.PRO LP7-2

Бренд: PAC Страницы: 2

Бренд: Tvone Страницы: 16

Бренд: PRO SIGNAL Страницы: 2

MCT-2612 SERIES

Бренд: CTS Страницы: 2

Video Sweep Generator MVG 10

Бренд: Kathrein Страницы: 28

CPSPI3700EVF380

Бренд: CyberPower Страницы: 94

225 Watt Power Inverter

Бренд: Vector Страницы: 6

Бренд: ClickTronic Страницы: 42

E-PSW-SX-01(SC)

Бренд: Transition Networks Страницы: 6

Бренд: Sabaj Страницы: 18

DIGITAL plus LE1000W

Бренд: Lenz Elektronik Страницы: 8

Бренд: Hitachi Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды