Generac Mobile MMG35DF4 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 60

Generac Mobile MMG35DF4 Скачать руководство пользователя страница 10

6

Owner’s Manual for Mobile Generator

Introduction and Safety

•

DO NOT

tow trailer using defective parts. Inspect

the hitch and coupling for wear or damage.

•

Connect safety chains in a crossing pattern under
the tongue.

•

Before towing the unit, verify the weight of the
trailer is equal across all tires. On trailers with
adjustable height hitches, adjust the angle of the
trailer tongue to keep the trailer as level as
possible.

Safe Towing Techniques

•

Practice turning, stopping and backing up in an
area away from heavy traffic prior to transporting
the unit.

•

Maximum recommended speed for highway towing
is 45 mph (72 km/h). Recommended off-road
towing speed is 10 mph (16 km/h) or less,
depending on terrain.

•

When towing, maintain extra space between
vehicles and avoid soft shoulders, curbs and
sudden lane changes.

Reporting Trailer Safety Defects

If you believe your trailer has a defect which could cause
a crash or could cause injury or death, you should
immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Generac
Mobile.

If NHTSA receives similar complaints, it may open an
investigation; and if it finds that a safety defect exists in a
group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in
an individual problem between you, your GMASD, or
Generac Mobile.

To contact NHTSA, you may either call the Auto Safety
Hotline toll-free at 1-888-327-4236 (TTY:1-800-424-9153),
go to

http://www.safercar.gov

; or write to:

Administrator

NHTSA

1200 New Jersey Avenue S.E.

Washington, DC 20590

You can also obtain other information about motor vehicle
safety from

http://www.safercar.gov

.

«
...
8
9
10
11
12
...
»

Содержание MMG35DF4





























































Отзывы:

Нет отзывов