Generac Mobile MMG35DF4 Скачать руководство пользователя страница 11

Страница: 11 / 60

Owner’s Manual for Mobile Generator

Introduction and Safety

Safety and Operating Decals

This unit features numerous safety and operating decals.
These decals provide important operating instructions and
warn of dangers and hazards. The following diagrams
illustrate decal locations and descriptions.

Replace any missing or hard-to-read decals and use care
when washing or cleaning the unit. Decal part numbers
can be found in the parts manual at

www.generacmobileproducts.com.

Description

Towing Instructions

Starting and Stopping Generator

Ultra Low Sulfur Fuel Only

Operating Instructions

Danger: Diesel Fuel

Terminal Connections (Voltage Selector Switch)

Tie-Down Location

Electrical Backfeed Danger

Oil Drain

Remote Start Terminal Connections

Coolant Drain

Neutral Bonded to Frame

Warning: Hot Surface

CAM Locks

Unit Lift Point

Connection Terminal Lugs

Warning: Automatic Starting

Fan Clutch (if equipped)

Electric Shock Hazard

Fuel Heater (if equipped)

Warning: Hot Surface

Start/Prestart

Do Not Operate with Guards Removed

Fuel Transfer

Ground

Danger: Read Owner’s Manual Before Operation

Battery Disconnect

Circuit Breaker

Secondary Filter

Breaker

Primary Filter

Controller Toggle Switches

Warning: Hot Surface/Moving Parts

Read Owner’s Manual Before Operation

Open Upper Door First

—

Содержание MMG35DF4





























































Результаты поиска

Содержание MMG35DF4

Отзывы:

Generac Mobile MMG35DF4, Руководство пользователя, Страница: 11 / 60

Результаты поиска

Содержание MMG35DF4

Отзывы: