manualshive.com logo in svg

Generac Mobile CTF10, Руководство пользователя

Поделиться
Скачать
Generac Mobile CTF10 Скачать руководство пользователя страница 27

Owner’s Manual for CTF10 Light Tower

23

Troubleshooting

Section 5: Troubleshooting

Troubleshooting the Lights

(000343)

Electrocution. Potentially lethal voltages are present
in this equipment. Render the equipment safe before
attempting repairs or maintenance. Failure to do so
will result in death or serious injury.

DANGER

IMPORTANT NOTE: 

Only a qualified electrician should 

troubleshoot or repair electrical problems occurring in this 
equipment. Contact Generac Mobile Products Technical 
Service at 1-800-926-9768 for assistance if you have any 
questions, or if problems persist.

Problem

Possible Cause

Solution

LED Mast Lights 
Do Not Turn On

Extension cord too 
long

Use an appropriately sized extension cord. See 

Table

 

3-1: Rec-

ommended Shore Power Cable Size and Length

.

Faulty electrical 
connection

Verify no loose connections in the following:

• Mast junction box
• Pin connector
• LED driver connectors (input/output on each driver)
• Mast light circuit breakers (4)
• Input power selector
• Switch
• Main breaker switch

Faulty main breaker 
switch

Replace main breaker switch.

Faulty mast light 
circuit breaker(s)

Replace mast light circuit breaker(s).

Faulty LED driver

Verify driver input voltage from input connector is 120 VAC  
±10 VAC. If output voltage from LED Driver is less than 40 VDC, 
replace LED driver

Supply power breaker 
tripped

Reset supply power breaker.

Extension cord gauge 
too small

Use an appropriately sized extension cord. See 

Table

 

3-1: 

Recommended Shore Power Cable Size and Length

.

LED Mast Lights 
are Flashing

LED driver 
overheated

Leave light off for a few minutes to reset protection, then restart 
lights.

Voltage is too low

Verify nothing is obstructing airflow to driver. Check for 
accumulated dust or dirt on driver; remove using clean, dry cloth.

Main Breaker 
Switch Trips when 
Applying Load

Connected load 
(through GFCI) too 
large

Reduce size of connected load or reduce the number of lights in 
use.

Содержание CTF10

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды