background image

 

 

 
Edificio Genebre. Av. de Joan Carles I, 46-48 
08908 L'Hospitalet de Llobregat. Barcelona (Spain) 
[email protected]   - www.genebre.es 

 

 

GENEBRE S.A. 

FECHA DE REVISIÓN: 07/05/2019         NUMERO DE REVISIÓN:  2 

 
 

 
1. Product Description

    

 

 

The  Digital  Positioner  is  a  fitting  the  electric  actuator  to  convert  the  actuator  in  a  self-
control valve positioner. 
 
The Digital Positioner is a modulus with a microprocessor (CPU) which manages digitally 
the analogical input and output and compare them with the position of the actuator to 
establish an uniform relation. 

 
 

The analogical inputs are sent to CPU where they are processed for his continuous 
comparison with the position of the actuator, this allows to obtain a very high sensitivity 
next to a very high repetitivity of the position (see characteristics). 

 

The Digital Positioner in communication with the electronic system of the actuator 
provides an integral management of the motion on the actuator. 

 

Sign position input is converted to a digital numerical value and is continuously compared 
with the position of potentiometer which is mechanically fitted to the valve shaft. 
 
The programme in the microchip makes all the necessary calculations to determine which 
way the motor should turn so that the potentiometer position and the valve corresponds 
to the position, it keeps the motor in stopped position until it receives an input signal.

 

 

 

 
2. Safety Instructions  

 
 

The scope of this manual is to enable a competent user to install, operate, adjust and 
inspect a Digital Positioning System to GE quarter turn electric actuator. These 
instructions must be observed, otherwise a safe operation of the actuator is no longer 
warranted.

 

 
 
 

 

  

 

 
 
 
 

As electric device, during electrical operation certain parts inevitably carry 
lethal voltages and currents (ELECTRICAL RISKS). Work on the electrical 
system or equipment must only be carried out by a skilled electrician himself or 
by specially instructed personnel, in accordance with the applicable electrical 
engineering rules, health and safety Directives and any other 

national legislation 

applicable. 

 

Содержание 5810 04










Отзывы: