manualshive.com logo in svg

Gemlight GMB-486UN, Руководство пользователя

Поделиться
Скачать
Gemlight GMB-486UN Скачать руководство пользователя страница 26

Mainboard Installation

3.5.8  J1-KEYBOARD  CONNECTOR

A standard five-pin female DIM keyboard connector is located at the rear of
the keyboard.  Plug the jack on the keyboard cable into this connector.

Pin

Description

1

Keyboard Clock

2

Keyboard Data

3

Spare

4

Ground

5

+5V  DC

Table 15

3.6

SYSTEM  ASSEMBLY  OVERVIEW

After installing and connecting the mainboard, assemble components in the
following order:
1.

Power Supply:  Place the power supply so that it fits the raised
tongues on chassis floor.  Insert and fasten 2 screws on the back panel
of chassis.  Connect power supply to connector, J2/J3.

2.

Disk Drives:  Slide disk drives into the chassis.  Connect a wide 34-
wire ribbon cable to each disk drive which will attach to an adapter
card.  Connect the 4 power supply cables to disk drives.

3.

Adapter Cards:  Insert each adapter card -- Disk Controller cards,
Video card, Serial/Parallel Interface card, etc, into an expansion slot.
Refer to the installation and configuration instructions that come with
the card.  Connect the disk drives to the Floppy Disk and Hard Disk
Controller cards.

4.

Keyboard:  Connect the keyboard to its connector, J1.

5.

Display:  Connect the display cable to the Video Card, and the
display's power cord into a power outlet.

6.

Case:  Slide on the case cover and fasten its screws.

Connect the power cord to the power supply and plug it into a wall outlet.  Put
the boot disk into drive A: and turn on the power.  User will then need to run
the BIOS setup program.

Содержание GMB-486UN










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды