Page 5
5. Tapping the START/STOP (39) button begins the sampling process
(the SAMPLER INDICATOR (37) will illuminate RED). Tapping the
START/STOP (39) button a second time ends the sample (the
SAMPLER INDICATOR (37) will turn off). If you do not tap the
START/STOP (39) button a second time, the sampling process will
stop automatically after 2, 4 or 12 seconds depending on which
MEMORY BANK (27) was selected.
SAMPLE PLAYBACK:
1. Put the MODE SELECTOR (34) switch into the SINGLE or REPEAT
position.
2. Select the memory bank you wish to play by pressing the proper
MEMORY BANK (27) button.
3. Tapping the START/STOP (39) button with the MODE SELECTOR
(34) switch in the SINGLE position will cause the sampler to
playback one time (the SAMPLER INDICATOR (37) will illuminate
GREEN). Every push of the START/STOP (39) button will restart the
sample from the beginning. Rapid pressing of the START/STOP (39)
button will cause a stuttering effect. Once the sample has started
playback and the START/STOP (39) button is not pushed a second
time, the sample will play to the end and then stop (the SAMPLER
INDICATOR (37) will turn off).
4. Tapping the START/STOP (39) button with the MODE SELECTOR
(34) switch in the REPEAT position will cause the sample to
continuously play over and over (the SAMPLER INDICATOR (37) will
illuminate GREEN). The START/STOP (39) button will act as an on/
off switch. The first push will start the sample, the second push will
stop it. The SAMPLER LEVEL (32) controls the level of the sample.
ROBO PLAY:
1. With the ROBO PLAY (36) button in the OFF POSITION (the ROBO
PLAY INDICATOR will be OFF) and the MODE SELECTOR (34)
switch in either the SINGLE or REPEAT mode, pressing the START/
STOP (39) button will cause the sample to play along with the
selected source.
2. When the ROBO PLAY (36) button is in the ON position (the ROBO
PLAY INDICATOR illuminates RED), starting the sampler mutes the
selected source. When the sample ends, the source automatically
turns back on.
BATTERY BACKUP: The PS-900 PRO is equipped with battery backup
to retain samples. To activate this feature, a 9 volt battery (not included)
needs to be connected to the BATTERY HOLDER (47) located on the
rear panel. This will enable you to store samples in memory, and when
the unit is unplugged, the battery backup will retain the samples for
future use. If the unit is unplugged with no battery attached, all the
samples will be lost.
LOW BATTERY INDICATOR: A low battery indicator is included with the
PS-900 PRO. When changing the battery, make sure the unit is plugged
in and the power is ON. Failure to adhere to this will result in lost
memory. The low battery indicator is ON when the selected memory
bank LED blinks. The LED will also blink if no battery is connected to the
unit.
Specifications
INPUTS:
DJ Mic....................................................1.5mV 2Kohm balanced
Phono.........................................................................3mV 47Kohm
Line.......................................................................150 mV 27Kohm
OUTPUTS:
Main/Aux......................................................0 dB 1V 400ohm
Max..............................20V Peak to Peak
Rec...........................................................................225mV 5Kohm
MIC 1 & MIC 2:
DJ Mic....................................................1.5mV 2Kohm balanced
Bass......................................................................................± 12dB
High.......................................................................................± 12dB
MIC 3:
DJ Mic....................................................1.5mV 2Kohm balanced
Controls...........................................................................Channel 4
GENERAL:
Bass (Chnls 1-4).......................................................+ 12dB/- 32 dB
Mid (Chnls 1-4)..........................................................+ 12dB/- 32 dB
Treble (Chnls 1-4).....................................................+ 12dB/- 32 dB
Gain (Chnls 1-4)..............................................................0 to -20dB
Frequency Response....................................20Hz - 20KHz +/- 2dB
Distortion................................................................................0.02%
S/N Ratio...............................................................better than 80dB
Talkover Attenuation..............................................................-16dB
Headphone Impedance.........................................................16ohm
Power Source.............................................115/230V 50/60Hz 10W
Dimensions.....................................................19”w x 4”h x 9”d
Weight........................................................................10.17 lbs
