(4
4)
Congratulations on purchasing a
Gemini iTT
fully manual high
torque turntable. This state of the art turntable includes the lat-
est features. Prior to use, we suggest that you carefully read all
the instructions.
- Fully Manual Direct Drive Turntable
- Super high torque (2.2 kg) direct drive turntable
- +/-10% variable pitch slide control
- Solid aluminum platter with easy glide grooves
- Straight tone arm for superior tracking
- Tone arm height adjustment up to 6 mm with lock
- Fully adjustable counter weight & anti-skating controls
- LED illuminated soft touch start/stop & RPM buttons
- 33/45/78 RPM
- Push button quartz lock w/ LED
- Target light with RCA connector
- Removable head shell
- Felt slip mat included
- Detachable RCA & ground cables
1. Read all operating instructions before using this equipment.
2. The apparatus should not be exposed to dripping or splash-
ing, and no objects filled with liquids such as vases should be
placed on the apparatus.
3. To reduce the risk of electrical shock,
DO NOT OPEN THE
UNIT
. Please contact the Gemini Service Department or your
authorized dealer to speak to a qualified service technician.
4. Tone Arm bearings are factory set and sealed. Any attempt at
adjustment will void the warranty.
5. Be sure that all
AC
power is
OFF
while making connections.
6. Cables should be low capacitance, shielded and of proper
length. Make sure that all plugs and jacks are tight and properly
connected.
7. Always, begin with the audio level faders/volume controls set
at minimum and the speaker volume control(s) set to
OFF
. Wait
8
to
10
seconds prior to turning up the speaker volume to pre-
vent the transient "POP" that could result in speaker/crossover
damage.
8.
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
.
9.
DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON
ANY CONTROLS OR SWITCHES
.
Please make sure the following parts are included with your
iTT
:
Turntable unit..........................................................................1
Turntable platter......................................................................1
Slipmat....................................................................................1
Counterweight........................................................................ 1
Headshell with cartridge.........................................................1
RCA target light……………………………….............…………1
SEE FIG. 3 FOR PART NUMBERS AND LOCATIONS.
VOLTAGE SELECTION:
Rotate the
PLATTER
(2) until the
VOLTAGE SELECTION
SWITCH
(3) (located on the
TURNTABLE BASE
(1)) is visible
through one of the platter holes. Make sure that the
VOLTAGE
SELECTOR SWITCH
(3) is set to the correct voltage.
WARNING: IF YOU TRY TO OPERATE THE TURNTABLE WITH THE INCOR-
RECT VOLTAGE SETTING, IT CAN DAMAGE YOUR TURNTABLE.
TURNTABLE INSTALLATION:
1. Put the
SLIPMAT
(4) on the
PLATTER
(2).
2. Set the
TURNTABLE BASE
(1) on a flat, level surface free of
vibration. Use the turntable feet to stabilize the unit horizontally.
3. Try to place the unit as far away from the speakers as possi-
ble.
4. Keep the unit away from direct exposure to the sun, heat,
moisture or dirt.
5. Keep the unit well ventilated.
CARTRIDGE INSTALLATION:
(SEE FIG. 1)
Because all cartridges have their own designs, please refer to
your particular cartridge's instructions to insure proper installa-
tion. If you are using a pre-mounted or integrated cartridge, you
can jump ahead to
HEADSHELL INSTALLATION
.
1. Connect the lead wires to the cartridge terminals. For your
convenience, the terminals of most cartridges are color-coded.
Connect each lead wire to the terminal of the same color. In
case your cartridge is not marked the positive leads are the ones
on top negative below, left are left, and right is right.
White (L+)................................................Left C
Blue (L-)...................................................Left Channel -
Red (R+)...............................................Right C
Green (R-).............................................Right Channel -
2. Mount the cartridge in the
HEADSHELL
(5) and tighten it with
the screws included with the cartridge.
HEADSHELL INSTALLATION:
Insert the
HEADSHELL
(5) into the front of the tubular
TONE
ARM
(7). While holding the
HEADSHELL
(5) firmly in a horizon-
tal position, turn the
LOCKING NUT
(6) counter clockwise until
the
HEADSHELL
(5) is locked in place.
COUNTERWEIGHT INSTALLATION:
(SEE FIG. 2)
1. Slide the
COUNTERWEIGHT
(8) onto the rear of the
TONE
ARM
(7) with the numbered stylus gauge facing forward.
2. Twist the
COUNTERWEIGHT
(8) counter clockwise lightly, to
screw it onto the rear of the
TONE ARM
(7).
ADJUSTING HORIZONTAL ZERO (0)
BALANCE AND STYLUS PRESSURE:
1. Without touching the stylus tip, remove the stylus protector (if
your cartridge has a detachable one).
2. Release the
ARM CLAMP
(10) and lift the
TONE ARM
(7) off
the
ARM REST
(11).
3. Counter clockwise advancement of the
COUNTERWEIGHT
(8) will cause the cartridge side of the
TONE ARM
(7) to be low-
ered; turning it clockwise will cause the opposite. Turn the
COUNTERWEIGHT
(8) clockwise or counter clockwise as need-
ed until the
TONE ARM
(7) is balanced horizontally. You can
INTRODUCTION:
FEATURES:
PRECAUTIONS:
I
N THE
USA ~
IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT
CALL
G
EMINI
C
USTOMER
S
ERVICE AT
: 1 (732) 738-9003. D
O NOT
ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER
.
PARTS CHECKLIST:
ASSEMBLY & SET-UP:
