3.0 - OPERATING INSTRUCTIONS
USER MANUAL
3.1 - COMPLETE SYSTEM ARMING
3.2 - SYSTEM ARMING WITH SENSORS EXCLUSION
Press the lock button on the vehicle remote control or button
system arming is confirmed by a siren chirp and a flash of the turn indicators (if optical/acoustic
signals are enabled).
The system has a 30 sec. arming delay during which the LED is ON steady.
To arm the system without arming interior protection press button “3” on the Gemini remote control.
“1” on the Gemini remote control (P/N
738W);
System arming is confirmed by a quick low-pitched chirp and a flash of the turn indicators (if signals
are enabled).
3.3 - PASSIVE ARMING
If programmed for passive arming, the system will automatically arm approximately 60 sec. after
ignition is switched OFF and the last door is opened and closed.
Arming is confirmed by a siren chirp and a flash of the turn indicators (if signals are enabled).
If programmed for passive arming, interior protection is excluded.
Opening a door during the 60-second passive-arming countdown will cause the
procedure to interrupt; it will resume once the door is closed.
3.4 - ARMING DELAY
There is a 30 sec. delay from the time the system is armed to allow you to leave the vehicle without
triggering an alarm: it will be signaled by the LED turned ON steady.
Exclusion of sensors is bound to each single arming cycle. They will be reset upon next
arming.
PAGE 04 - USER MANUAL
USER MANUAL - PAGE 05
3.7 - SYSTEM DISARMING
Press the unlock button on the vehicle original remote control or button
flashes of the turn
indicators (if signals are enabled).
Alarm causes and relative LED signals are listed in the next paragraph.
“2” on the Gemini remote
control (P/N 738W); system disarming is confirmed by 2 siren chirps and 2
If an alarm event has occurred while you were away from your vehicle, it will be signaled, when you
disarm the sytem, by 5 siren chirps and 5 flashes of the turn indicators.
3.8 - ALARM MEMORY
The LED memory allows to identify the last alarm event signaled by 5 siren chirps and 5 turn indicator
flashes when the system is disarmed.
Turn ignition key “ON”and count the number of flashes. The status LED will flash according to the last
alarm detected prior to disarming (see table below).
The flash sequence is repeated 3 times; to interrupt turn ignition key “OFF”.
The table below lists the various alarm causes and relative number of LED flashes.
LED FLASHES
ALARM CAUSES
ALARM
CYCLES
10
10
1
1
0
10
0
10
10
10
Ignition attempt (+15/54)
Boot tamper
Volumetric or external sensor
Wireless magnetic contacts or
opening detectors
Wireless infrared sensors (PIR)
Wire tampering
Door tamper
Bonnet tamper
LED ON (1 second)
LED OFF (2 seconds)
3.6 - ALARM, NEUTRAL TIME BETWEEN ALARMS AND ALARM CYCLES
Alarm events are signaled by optical/acoustic signals
Each alarm event can generate up to 10 cycles for each input and for each arming cycle. One alarm cycle
lasts for 30 sec.
. Once the alarm ceases, there is a 5 sec. time-
interval before another alarm can be triggered.
• FIAT DUCATO ‘11
• FORD TRANSIT ‘14
• RENAULT MASTER ‘10
›
›
›
Sensors can be excluded via the vehicle original remote control on the following vehicles:
To exclude interior protection via the vehicle original remote control, proceed as follows:
• Lock the vehicle via the vehicle original remote control.
• Wait at least 5 sec.,
, and press the lock button again.
• Exclusion is confirmed by 1 low-pitched chirp.
THIS CONFIRMATION TONE CANNOT BE EXCLUDED.
but before the end of the arming delay
NB:
3.5 - SYSTEM ARMED
After the arming delay the system is fully armed and ready to detect any alarm event. The LED will start
flashing to confirm the armed status.