Gemini 516MHW Скачать руководство пользователя страница 3

Страница: 3 / 9

Designed

and

manufactured

GEMINI

TECHNOLOGIES

srl

‐

Via

Galvani,

–

21020

Bodio

Lomnago

(VA)

–

Italy

Tel.

+39

0332

943211

–

Fax

+39

0332

948080

–

www.gemini

‐

alarm.com

ISO

9001

CERTIFIED

COMPANY

Rev.01

07/2018

3/9

System performance will depend on the correct positioning and angling of the sensors.

Accurately calculate and mark the sensor positions on the bumper.

Remove the bumper and make sure there are no obstructions that may hinder the fitting of the sensor heads and the control unit (ECU).

Use a small diameter bit to drill pilot holes for each sensor.

Finish the holes to the proper diameter using a cone drill bit that matches the diameter of the selected adapters.

Determine the correct mounting height and position to achieve the best detecting angle and distance (the figures shown below are purely indicative).



Installation and connections should only be done by qualified personnel.



Disconnect the negative battery terminal before doing any electrical work.



Some bumpers have factory markings on the inner side; before drilling any holes, make sure they correspond to the recommended positions.



Some bumpers require correction adapters around the sensors to obtain the proper fitting angle.

6.0 - INSTALLATION PRECAUTIONS

7.0 - PREPARING FOR INSTALLATION

8.0 - INDICATIVE SENSOR SPACING AND HEIGHT

Содержание 516MHW










Результаты поиска

Содержание 516MHW

Отзывы:

Бренды по названию

Популярные бренды

Gemini 516MHW, Руководство пользователя

Результаты поиска

Содержание 516MHW

Отзывы:

Бренды по названию

Популярные бренды