Gemco Semelex Safetimeter 1999 Series Скачать руководство пользователя

Страница: 17 / 18

Operation Manual

Toll Free: 800-635-0289 • Email: [email protected] • Web: www.ametekfactoryautomation.com

Specifications

Electronics
Display

7-Segment Red LED

Stopping Time (Ts)

9.999 Seconds - Maximum

Safety Distance (Ds)

999.9 Inches - Maximum

Accuracy

+/- 1% of Reading

Press Stroke

49 inches - Maximum

Power Supply

115 Vac - 50/60Hz Supply/Charger
6VDC Rechargeable Battery

Battery Type

6 Volt, sealed lead acid

Operating Time

(Full Charge) 10 hours (Continuous)
Between Charges - 3-5 Days Typical On/Off

Recharge Time

8 Hours

Mechanical
Safetimeter Case

Highly Visible Yellow Plastic Case
14.92””L x 13.00””W x 6.82”H.
Weight: 17.9 lbs.

Auto-Hand

Material: Aluminum. Finish: anodized.
Dimensions: 4.5” dia. x 2” H.
Weight: 3.2 lbs.

P/V Transducer

Material: Aluminum. Finish: anodized
Dimensions (cable magnet extended):
5.25”L x 2.75”W x 4.75”H.
Maximum Cable Stroke: 49”
Weight: 1.6lbs.

Specifications are subject to change without notice

Dimensions - Case

Содержание Semelex Safetimeter 1999 Series



















Результаты поиска

Содержание Semelex Safetimeter 1999 Series

Отзывы:

Похожие инструкции для Semelex Safetimeter 1999 Series

Бренды по названию

Популярные бренды

Gemco Semelex Safetimeter 1999 Series, Руководство по эксплуатации

Результаты поиска

Содержание Semelex Safetimeter 1999 Series

Отзывы:

Похожие инструкции для Semelex Safetimeter 1999 Series

Бренды по названию

Популярные бренды